JVM1860SF001 General Electric Microwave - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Griding Sound From Microwave when Running
First had to figure out where the sound was comming from. Took off the bottom cover and saw the Glass Cooking Tray Drive Motor. I had to take the motor off and turn the microwave on to verify that was where the sound was comming from. Apparently the microwave itself was amplyfing a slight grinding that was comming from the motor. I ordered the part; Only took 48 hours to receive the part! Swapped the motor out in 10 minutes and saved $300 for a new microwave.
Parts Used:
-
Rodney from St. Augustine, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No heat.
-
Mack from Jacksonville, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
glass light lens were broken
All one has to do is use a screw driver to remove the screws, one per lens.
Then lower the lens bracket, bend the 4 tabs holding the
lens, remove and replace the lens and screw the brackets back in place.
Less than 10 minuits.
Then lower the lens bracket, bend the 4 tabs holding the
lens, remove and replace the lens and screw the brackets back in place.
Less than 10 minuits.
Parts Used:
-
Hugh from Slippery Rock, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The motor that turns the turntable stopped working.
Only needed a phillips screwdriver to remove screws from the bottom of the microwave. Unplugged the motor, removed the two screws holding it in place, put the new motor in place replaced the screws, and replaced the bottom. It took about 10 min.
Parts Used:
-
Jeffery C. from Sturgeon Bay, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Right Front Rack Holder
Removed the broken rack holder and replaced it with a new one. I ordered extra ones for the next one that breaks.
Parts Used:
-
Jim from Anchorage, AK
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Tray did not turn
Removed the bottom of microwave , removed the tray motor and replaced with new motor. total time 10 min.
Simple
Simple
Parts Used:
-
leo from mequon, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bulbs Burnt Out
Removed old bulbs replaced with new. Bulb fit perfect thank you
Parts Used:
-
DOMINICK from VENICE, FL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Turntable stopped Turning
Unplugged electrical power, exposed the lower cover, Unplugged wiring to old Motor, removed 2 screws holding old Motor in place. - Reversed procedures with new part.-
Glad I found your Services :-)
Thanks.
Glad I found your Services :-)
Thanks.
Parts Used:
-
Lawrence from San Diego, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
microwave lamp was burned out
took glass cover off being an electrician and saw lamp or bulb was burned out. googled your site and with model number.went on partselect found lamp,orderd it.2 days later lamp arived installed lamp. So easy no running around or making several calls
Parts Used:
-
Timothy from Swampscott, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
turntable would not turn/motor froze
could not have been any easier to replce motor . unplug unit,remove 7 screws, drop down bottom plate, unplug motor, remove 2 screws and replace motor. reverse steps to finish installation.
Parts Used:
-
Michael from Silverdale, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Changing Turntable motor
Repair went smoother than expected, but a couple of comments should be made. The screws are easy to see and to remove from the bottom plate of the Microwave. The inside of the plate, where the light and filter are can be really greasy and icky. The motor was easy to replace. Putting the screws back in can be relatively tough - especially the ones in the back. I lost one. Might be good to be better prepared to make sure that they don't drop behind the counter.
Parts Used:
-
Claus from Prior Lake, MN
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drive motor failed
Removed screws from underside of micrwave to get at drive motor, removed screws for drive motor and reversed the process to complete the repair.
Parts Used:
-
George from West Groton, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave turntable would not turn
Unplug unit from AC source. Removed turntable and gear from inside of microwave. removed bottom plate (5 screws) and removed 2 screws that held motor. Unplug wires from motor and replace new motor in reverse.
Parts Used:
-
Eddie from Clyde, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light Bulbs Failed
Used a phillips screwdriver to remove the screw holding the light cover in place. Removed the two bulbs and replaced them. Closed the cover and tightened the screw
Parts Used:
-
Wilbert from Stephens City, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Turntable wouldn't turn
Removed five screws from the bottom of the microwave, panel hinged down and exposed the motor. Removed one screw, replaced motor, and put the panel back in place. It took a little longer because I took the oportunity to clean it out!Also I now know how to get to the lights.
Parts Used:
-
Daniel from Mountain House, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!