JVM1490SD003 General Electric Microwave - Instructions

This was the second time I've had to open up the microwave. 1st time display would blank out but system would continue to operate. Found solder connections on board to LED display were defective. Resoldered and unit was fine. This time I found the connection to the oven cavity temp cut-off was bad, plastic connection cover melted. When unit operated bottom lead and wire would heat up. Couldn't measure a Discernable distance so either wire or connector connection surface was not sufficient to carry the current. 1st replaced sensor still wire heated up. Replaced connector and there was no sign how heat from resistances.

One small Phillips screwdriver and one fuse puller (I used cord). Unplug unit. Remove the two screws on the vent face plate. Remove the one screw on the panel assembly. Gently let hang. Pull the fuse located on the upper left wall. Replace fuse. Reassemble.

the main issue I had is the appliance manual stating that the bulb should be "unscrewed". when I first read the manual, before I received the bulb on delivery, I tried "unscrewing" the bulb, which actually is a PLUG IN bulb. small wonder that it didn't come out! luckily I didn't break the connections off in the socket!

Finnaly found exploded view of door, but had to guess how to remove snap in escution that covered the screws. Broken end of old handel piece spins with screw, so I am waiting for help to hold the front end, so I can remove the screw from the other side. Repair has yet to be completed!

The repair was very simple. I removed the broken grille and replaced it with the new one using only a screw driver . The procedure took less than five min. I was very pleased with the price of the new grille, which was less than the you know who, and how fast it took the part to reach my home. You get an a+ from me.

removed light cover and replaced defective bulb

Remove the bottom of the microwave and remove/replace table motor.

Over the stove microwave installed in top cabinet row.
1. Unplug device.
2. Two people to remove from wall/cabinet (remove two, large, top mounting screws and rotate entire microwave down and off the wall mount). Should be some wood spacers between top of device and bottom of cabinet.
3. Remove screws from sheet metal cover.
4. Remove one screw holding blowers in place and rotate out of the way, in order to gain access to 2 of 5 screws that hold the magnetron in place.
5. Unplug magnetron and remove the 5 screws.
6. Drop in new magnetron and re-assemble microwave in reverse order (steps 5-3).
7. Two people restore micro to wall/cabinet. Replace wood spacers, re-install two, large mounting screws (finger-tight). Test device. Secure the two large screws.

First I removed the inside of the door using a putty knife and loosening the edges. I removed the old latch by- (1) lifting up and sliding both the top and the bottom out of the door (2) pulling out the bottom part and (3) using a small plastic fork to push the spring off of the top part (paying close attention to how it was already sitting in the microwave). It required a little twisting (not much) and it came out.

I put the new spring on the new piece on the hook part. Then I put the new spring on the oven (where the old spring had been). I stretched the latch up and put the top slot back in and then with a little (very little) pressure I popped the bottom back in.

First remove all screws holding on outer metal casing of microwave. Next remove the back and bottom metal pieces. You will then be able to pull aside the outer casing so you can access the door switches. Check each switch with an ohm meter in both the open position and with the switch closed. If the ohm meter reads the same in both the open and closed position, the switch is bad. Check the top switch first. Replace switch and reassemble. Cheap fix for a costly microwave. Great customer service at Parts Select!

I attached the mounting plate to the wall as directed in the installation instructions which I had downloaded from GE. This procedure took 45 minutes to complete. I was then able to mount the microwave.

The actual repair required removing wave guide held in by one phillips screw was easy.

Thanks much for your rapid dependable delivery!!!

Norm Goetzke
West St. Paul, MN.

unplugged power cable / unhooked front vent / unscrew the monitor panel / slide up to dislodge / take the fuse out and put in the new one in / fuse is located right in front of monitor panel once its open might be covered by wirings / you can unpin the cables from the panel to make it easier for you just make sure to put it back properly or you can have somebody hold the panel for you. Installing the fuse is easy waiting for the parts is crazy......

Disassembled the front cover, found slow blow fuses, then replaced with microwave fuses 250V-20Amp. Utilized a few fuses to pin point the problem, Microwave functions all worked except the express feature, made an assumption after using a tester that it was the high voltage capacitor and the diode that attaches. Replaced both, plugged in and tested. Worked! reinstalled the unit. Sucessfull for the past month.

Had to remove the interior cover of the door to access the handle screws. Remove these screws and insert the new handle. This is a stovetop model so between the constant pushing and pulling on the handle together with the heat from the stove, the handle breaks. This is the second time I've had to replace it in 5 years...but again, it's an easy inexpensive fix.