Models > JVM1350WW02 > Instructions

JVM1350WW02 General Electric Microwave - Instructions

All installation instructions for JVM1350WW02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JVM1350WW02
121-135 of 234
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

light out over stove

  • Customer: virginia from hilton head island, SC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
so easy, but how do i turn light off?

Part recieved next day. thanks so much

Underneath Light On Microwave Would Not Come On.

  • Customer: MARY from PLYMOUTH, MA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
My son=law did repair because I am elderly and it was necesary to remove the bottom plate of the microwave which I was unable to do. The microwave was installed in 1987 and I believe this was the first time to replace the bulbs. When my son removed them the bulb was diintergrated. That's how old they were. Once he was able to remove the underneath plate the repair was easy except for removing the old bulbs. I think that I could have done it myself but he was available and I am sure it was done much better. All in all the parts)bulbs) were correct and everything is workiin fine. This is a good place to order replacement parts. In fact I am going to order a new charcoal filter. He took the label off the old one and I am ordering the replacement. After all 1987 may have been a good year, but time for a new one. Mary

door handle broken

  • Customer: Larry from Ocean Springs, MS
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 4 people found this instruction helpful
removed gasket inside door, removed 2 screws, pulled handle off, put new handle in place, put the 2 screws back onto handle, replaced gasket. finished.

Microwave oven handle broke when the door was opened...

  • Customer: shaun from Sterling, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Took a while to get around to ordering the part, which was beginning to drive my wife crazy, so I ordered the part without saying a word. The handle arrived within two days and I had the part installed within 10 minutes of opening the package, it was really easy. So, I had to trick her into opening the oven and it completely surprised her that it was done so quickly without her knowing a thing about it. Great service, thanks!

Handle broke off

  • Customer: Staci from Nine Mile Falls, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
The repair was so easy. I removed the one remaining screw, pulled out the rubber gasket, screwed in the new handle, replaced the gasket around the window and that's it. I swear it took less than 10 minutes.

broken door handle on built in microwave

  • Customer: gary from Park City, UT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
The repair hint on prying out the inner seal on the door for access to the second door mounting screw made the repair easy. Total time to replace the handle less then two minutes.

Microwave handle broke...plastic cracked

  • Customer: Robert from Lake Wales, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I removed the screw at the top that was exposed, but I couldn't figure out how to get to the second screw that was obviously holding the bottom of the handle in place. After a few minutes, I discovered that a plastic grommet on the inside of the microwave door was removable and allowed me access to the second screw. Once it was removed, putting the new handle in place was easy!

Bottom of door handle broke off - tried to superglue-didn't hold

  • Customer: Ken from Dacula, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
As others had done, I unscrewed the top screw inside the door - used a flat blade screwdriver to pop out the molding on the inside of the door covering the lower screw - loosened the screw and took the old handle off...installed the new, snapped the molding back on - and done.

Broken Handle

  • Customer: James from Grayslake, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
It took all of 3 minutes to fix! Using a phillips screwdriver, unscrew top screw. I then used a putty knife to pry the seal ring open to reveal the bottom screw. I then used plyers to hold the broken plastic piece and removed the bottom screw. Hold the handle in place and screw in bottom screw, then snap seal ring back into place and replace top screw. I was shocked at how easy this was and also how fast the part was shipped. I was very pleased. Thank You!!!

broken handle

  • Customer: Herold N from Boca Grande, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Very simple to replace. I followed another persons comments and it worked in 5-10 min.....the tip on removing the inside screen to expose the lower screw was perfect...i was very pleased with parts select....easy people to talk to and they provided the exact part i needed....i would use them for sure again ! H. Neal Billman Boca Grande, Fla

BURNED OUT (and broken) LIGHT BULB

  • Customer: WILLIAM from BONITA SPRINGS, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
With many thanks to those who posted their experience and advice replacing the bulb, I was able to remove 5 of the 6 screws holding the underside panel and remove the socket which contained the broken off base of the bulb and extract it with needle-nose pliers. I had broken off the glass portion of the bulb trying to unscrew it due to the awkward contortion of my wrist-hand-fingers trying to grip the bulb inside the tight recess the bulb is mounted in. After concluding that I needed more information, I did a web search for 'Hotpoint RVM1435' and found helpful advice at partselect.com telling me to drop the bottom panel. Good call! Thanks everyone!

Broken Door Handle

  • Customer: Elizabeth from Vero Beach, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I went online and found the replacement handle. I ordered it and it showed up one day later!! Excellent service.

the original handle broke

  • Customer: Joseph from Clemmons, NC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
The top screw was easy to access, and the lower screw required prying back a trim piece on the inside of the door.

Door Handle Broken

  • Customer: Othon from Walnut Creek, CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Unscrewed two screws, easily cleaned and replaced. Only difficulty was in figuring out how to remove the bottom screw. Not immediately apparent, but if you can manage to wedge out the gasket surround that circles the periphery of the door (alongside the inside), then you will have access to the phillips screw holding the handle in place. Carefully displace just enough to get access to the screw and return as you found it. Easy once you figure out how to remove the second screw.

Turntable problem.

  • Customer: Timothy from Hillsborough, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 4 people found this instruction helpful
Removed broken coulper.Snaped new coulping in placed.job done.
All Instructions for the JVM1350WW02
121-135 of 234