Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JVM1350WW02 > Instructions

JVM1350WW02 General Electric Microwave - Instructions

All installation instructions for JVM1350WW02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JVM1350WW02
61-75 of 234
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Micrwave won't run - turntable turns backwards when door opened...

  • Customer: Roger from Fountain Hills, AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 3 people found this instruction helpful
Most of the effort is simply getting the oven out of the built in enclosure and the sheet metal off. This take about 15 minutes then you have to remove the two screws (not handy location) that hold the door latch/switch assembly so you can remove the switch. I did this BEFORE ordering so I could test the switch (it was charred) and verify the part needed. WATCH OUT - some ovens use a normally open an some a normally closed version of this switch - you have to get the right one. I checked several suppliers that were showing the WRONG switch for my model. PartSelect had it right. Once I received the switch I had it on and the oven installed and running in less than 30 miutes. Working fine since then...

Broken glass and bad bulb

  • Customer: Chris from Destin, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
Removed one screw, slid frame out and removed broken glass. replaced bulb. The hard part was slidding the frame back in place and starting the screw. We were very surprised at the fast delivery of the parts, thank you. The sad part, a few days later the glass broke again. We are trying to get to the people at GE to solve our problem. We feel like that will not happen, we just do not have the time to stay on hold on the phone waiting for someone to solve our problem. Will reorder glass.

Door Handle Broke

  • Customer: Janie from Ruskin, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
Pry out plastic flange on inside of door...exposing to two screws (top of handle/bottom of handle) that attached plastic handle to oven door.
Removed the two screws and discarded broken handle..
Placed new handle on outside of door and replaced the two screws that secure handle to door.
Snapped inside flange cover in place...
Repair completed...
15 minutes...

Microwave Handle snapped!

  • Customer: Judith from Pflugerville, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
Imagine the surprise on my daughter's face when she went to open the microwave and the handle broke in half! I called multiple places locally, and ten days was the soonest I could find the part. I went online and ordered from PartSelect....three days later we were back in business. Good job, guys! And I installed it myself! A single mom from Texas

bulb fused to jolder

  • Customer: James from Big Rock, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
removed electrical wires, unscrewed holder, inserted holder, attached wires, added bulb, and put cover back on.

Power worked but would not cook

  • Customer: Jim from Albuquerque, NM
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Took the front panel off, played with the switch while it was plugged in to verify the switch was bad. I actually was able to tweak the switch just right to keep the microwave working while the part was being delivered. When it came it was just removing two small screws and replacing. Very easy.

Microwave would turn on when door opened

  • Customer: Lois from El Segundo, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 7 people found this instruction helpful
Unscrewed numerous screws holding the "body/shell" to the microwave. Removed body. I then unplugged top door switch, replaced it with new one, and "tested" the new one. I fixed our $400 convection micro with an $18 switch. NICE!

Lens Was Not Sized To Fit And Was Left Extremely Sharp

  • Customer: robert from salmon, ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Had to take to a local glass shop for sizing and to remove sharp edges. Will never order again.

microwave would not start

  • Customer: JULIA from JACKSONVILLE, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 10 people found this instruction helpful
took of cover removed switch and replaced with new one

Microwave appeared to work. Fan worked, timer worked plate rotated. It just didn't heat the food!

  • Customer: Mark from Hanover Park, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 10 people found this instruction helpful
I purchased the fuse and 3 door switches from PartSelect. Replaced the fuse first but that did not solve the problem. Then I replaced the 3 door switches and problem solved!! So fuse only cost $5.00 so glad I have a new fuse in there as well. To see how to replace door switches see videos on utube!!

turntable not turning

  • Customer: randy from navarre, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 5 people found this instruction helpful
after dealing with the turntable in my microwave not turning for a couple years i decided it was time to fix it.Checked it out and found the turntable motor bad.I looked on line for pricing and availability,ordered the part from partselect.Two days later the part was at my door.Thirty minutes, a few screws and a couple spade connectors later, my microwave was working like brand new.Making myself and more impotantly my wife real happy.It was a very easy repair,next time I won't wait so long!

Broken Light Socket

  • Customer: Richard from Batavia, OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
Turned the power to the unit off. Removed seven- (7) small screws from the base plate, not removing the rear screws. The plate dropped a few inches allowing me to get to the light socket. I removed one- (1) screw that allowed the socket to be removed. I then detached the two- (2) electrical leads. I now installed the new socket, replacing the leads and the screw along with a new bulb. I pushed the bottom plate back into the up position and replaced the seven- (7) screws. Turned the power back on and we were good to go.

NO light

  • Customer: Dan from Leesburg, FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
.Thank You Dan

Light bulb burned out and assembly broke when trying to replace bulb

  • Customer: Jeanne from Kirkwood, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
I used the internet and your directions to complete the repair. It was easy!

Microwave wouldn't start after "Start" pushed

  • Customer: Don from Monte Sereno, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
Took cover off, noted the two side by side switches easily visible and we hought one of these was responsible. Then son noted a third switch at the top of the plastic assembly which inserts at an odd angle. When it was inspected signs of a previous short showed up with burnt contact points. Reinserted at same odd angle as there were guide holes, closed things up and oven worked 100%. Great prompt service and great website!! We will use you again
All Instructions for the JVM1350WW02
61-75 of 234