Models > JVM1350WW02 > Instructions

JVM1350WW02 General Electric Microwave - Instructions

All installation instructions for JVM1350WW02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JVM1350WW02
136-150 of 233
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken Handle

  • Customer: James from Grayslake IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
It took all of 3 minutes to fix! Using a phillips screwdriver, unscrew top screw. I then used a putty knife to pry the seal ring open to reveal the bottom screw. I then used plyers to hold the broken plastic piece and removed the bottom screw. Hold the handle in place and screw in bottom screw, then snap seal ring back into place and replace top screw. I was shocked at how easy this was and also how fast the part was shipped. I was very pleased. Thank You!!!

broken handle

  • Customer: Herold N from Boca Grande FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Very simple to replace. I followed another persons comments and it worked in 5-10 min.....the tip on removing the inside screen to expose the lower screw was perfect...i was very pleased with parts select....easy people to talk to and they provided the exact part i needed....i would use them for sure again ! H. Neal Billman Boca Grande, Fla

BURNED OUT (and broken) LIGHT BULB

  • Customer: WILLIAM from BONITA SPRINGS FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
With many thanks to those who posted their experience and advice replacing the bulb, I was able to remove 5 of the 6 screws holding the underside panel and remove the socket which contained the broken off base of the bulb and extract it with needle-nose pliers. I had broken off the glass portion of the bulb trying to unscrew it due to the awkward contortion of my wrist-hand-fingers trying to grip the bulb inside the tight recess the bulb is mounted in. After concluding that I needed more information, I did a web search for 'Hotpoint RVM1435' and found helpful advice at partselect.com telling me to drop the bottom panel. Good call! Thanks everyone!

Handle broke

  • Customer: Kim from Centennial CO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
My husband took out the 2 screws from the inside of the microwave door and the ring inside the door. The bottom screw is behind the ring. Then the handle came off. Then he put the new handle in place, screwed the 2 screws back in and the ring. It was all done in 5 minutes. Very easy for him.

The bulbs burned out, the glass lens cracked and the light socket broke when trying to remove the bulb

  • Customer: Warren from Council Bluffs IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Replaced the sockets, lens and bulbs. The first time the new bulb was touching the lens and the heat broke the lens and burnt out the bulb. The second time I adjusted the socket so that the bulb does not touch the lens.

Impressed by how quickly the parts arrived after the order was submitted. Two days.

Thank you.

Replace the microwave door handle

  • Customer: Herbert from Burke VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
Once I read about the microwave door handle replacement on the internet, I thought that this was a do-able job. Fellow repair people wrote clear articles on the internet and the diagrams of the microwave door were great and explained the procedure well. The cost of the door handle was about $80, and it was delivered in 5 days.

time would count down but unit would not run & heat.

  • Customer: Bill from Shawnee OK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
remove cover, unplug secondary door switch (top switch)
remove switch from holder, install new switch, plug in wires, replace cover, very easy. door switches are a common problem
with microwave ovens.

Broken light lense

  • Customer: George from Marana AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Removed one screw, installed new lense in lense frame, rescrewed. Done.

bulb burned out -cracked holder lamp

  • Customer: Terry from Justice IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
pluged wires back on ,placed lamp holder and bulb back and replaced screws

Broken door handle

  • Customer: Scott from New Berlin WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Simple Simon...and I'm not handy. Remove top visible screw. Peel back gasket with butter knife to expose lower screw. Remove lower screw. Remove broken handle. Attach new handle with existing screws. Pop gasket back in place. DONE. 66 seconds.

Door handle broke off

  • Customer: Joellen from Castroville TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Repair was super easy. All I had to do pop out the band on the inside of door, remove screws from previous handle. I put new handle in place and screwed back in and pushed the band back into place. Super easy and only took like 10 minutes.

handle broke on microwave door

  • Customer: Holly from Eden Prairie MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
unscrewed the screws on the inside of the door. Handle came off and put new one on.

Plastic door handle broke off at bottom attachment

  • Customer: Dan S from Morgantown WV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
Other descriptions accurately describe how to replace the handle.

The microwave outer frame was broken. It is an old model

  • Customer: Nivea from Aliso Viejo CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
I searched in the website, I got the picture of the frame you had available for the Model and copied it in my computer. The frame had been placed on a graph paper. I counted the squares on the graph paper, measured the one I had and it was the same measurement. So, I ordered it.
We were able to install it perfectly well. WOW! THis is a lot easier than going around town looking for one and not finding it!
Thanks!!!

REPLACED OUTER DOOR FRAME AND HANDLE

  • Customer: Erik from Manhattan Beach CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
1) OPENED THE DOOR AND REMOVED INNER FACE FRAME.
REMOVED THE TWO SCREWS FOR HANDLE,
SLID OUT THE END SLID OUT THE GLASS.
SNAPPED THE PARTS INPLACE RE-INSTALLED THE GLASS, SCREWED IN NEW HANDLE AND DONE!
EASY DEAL!
All Instructions for the JVM1350WW02
136-150 of 233