Models > JVM1350WW02 > Instructions

JVM1350WW02 General Electric Microwave - Instructions

All installation instructions for JVM1350WW02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JVM1350WW02
1-15 of 233
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Microwave Cooking Tray Missing

  • Customer: Chris from Elmhurst NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 519 of 583 people found this instruction helpful
I ordered a microwave cooking tray from PartSelect; userfriendly site; and within two days, my part was delievered and easily installed. Thank you PartSelect!

Replace the door handle

  • Customer: Pat from Noble OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 460 of 461 people found this instruction helpful
Opened the microwave and locate the two screws that holds the door handle in place, unscrew the old handle then place the new handle make sure the orientation of the new handle is right.

Broken oven tray

  • Customer: Scott from Atlanta GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 438 of 516 people found this instruction helpful
replace new tray with no tools needed

the handle broke off the door of the microwave

  • Customer: Janet from BEDMINSTER NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 366 of 368 people found this instruction helpful
Removed the broken handle and replaced it with absolutely no problem. We thank you so much for having the part as we were sure we would have to buy a replacement microwave. This microwave was put into custom cabinetry so it was so great to be able to just purchase the handle!!!!!!!!

Handle broke where attached by screw

  • Customer: John from Mount Pleasant SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 158 of 223 people found this instruction helpful
Two screws had to be removed. One exposed with microwave door open. The other screw is hidden behind a plastic band around the perimeter of the door. Using a thin bladed knife I pried out the band all around the entire door. It comes out easily. This exposes the second screw to be removed. Then replace the door handle with both screws and press plastic band into place.

cooking tray brook

  • Customer: Giuseppe from Elmwood Park IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 138 of 216 people found this instruction helpful
none

Handle broke after 5 yrs of normal use.

  • Customer: Jeffrey from Charelston SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 117 of 180 people found this instruction helpful
1. I removed the top handle screw on the inside of the door (visible)
2. I removed the plastic seal from around the glass window on the inside of the door (pried out with screw driver; comes out easily)
3. I removed the lower handle screw on the inside of the door (hidden under the plastic seal)
4. Replaced the handle and screws
5. Re-installed the plastic seal
6. Door works like new.

I wasn't thrilled with the $65 cost (although PartSelect had the best price) but the ease of installation made me wish I had done it years ago. The buyer experience was OUTSTANDING. No problems. Rapid delivery.

THANKS!

light worked, timer and control pad worked, but no turntable, no heat, no noises of any sort, just didn't start up

  • Customer: Marla from Arlington TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 92 of 112 people found this instruction helpful
Noted on partselect.com that someone else with this problem, found it to be secondary door switch. There are three door switches in this model, but online info noted that one of the three might feel "soft" (in my case, one switch clicked in a rather "jiggly" way, the other two were strong decisive clicks.) To access the door switches on this model was the only difficult part. First use a torx bit to remove the two torx screws below the latches inside the microwave. This frees the latching part inside, that holds the door switches, which you will remove after you take off the control panel. The top grill has to come off before you can remove the door panel. Remove the screws above the grill, on the microwave top cover, The grill on this model is covered with a panel that moves out when it vents. After removing the two top screws, the covered grill vent slides left to remove. Be careful, as the sliding tabs are plastic. Wiggle and jiggle it, to slip it off. Below the removed grill, is a small metal grill with one screw in lower center. Remove that screw, and wiggle that out. You'll then see the one screw that holds on the control panel. Remove this screw, and lift the control panel up to remove. Again, go slowly and gently, as the bottom tabs holding the control panel in, are also plastic and easily broken. Lay the control panel on something, (I used the coffee maker) and pull out the wire bundles tucked on the left, that are attached to the latching panel. Wiggle the latching panel gently to lift it up off of it's plastic tabs and pull it out towards you, so you can see the three door switches. Each switch (part number WB24X829) has a little black switch on it. Feel each switch with either your finger, or a screwdriver to see which one doesn't "click" strongly. The weak one is the one you will replace. The door switches are fitted into a tab, and plugged into their wires. Remove the defective switch, pull out the wires, and replace it with the new switch, plugging back the wires, and slipping it back into it's plastic tabs. Then put everything back together in reverse order. The entire job took me fifteen minutes EXCEPT for figuring out how to slide off the upper grill, which I have told you. A repairman would have cost $150, the part was $18. AND, there's a good chance, the other two switches will get "used up" in the next year or so as well, so I'll be ready next time. Thank you, Partselect, why work all day, to make money, only to give it to somebody else, for fifteen minutes of work. All I needed was the knowledge.

Light bulb out, tried to remove, lamp socket broke

  • Customer: Gene from Urbana IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 84 of 94 people found this instruction helpful
Above the stove mounted microwave. I dropped the lens cover from under the bulb and tried to remove the bulb. The bulb separated from the base. I tried to remove the base with a pliers and the lamp socket broke. I ordered the parts and dropped the bottom cover of the unit down (5 screws). Removed 1 screww from the lamp socket, unplugged the wires and took it out. Simply replaced socket, fastened bottom cover of microwave, installed new bulb and closed lens cover.

cooking tray (glass) broke

  • Customer: Magda from Beverly Hills MI
  • Difficulty: Really easy
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 147 of 286 people found this instruction helpful
Took out broken piece
Called GE Parts to order replacement
Upon arrival, opened package, took out new part, inserted it where old part had been.

Broken carousel plate

  • Customer: Ronald from Casa Grande AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 142 of 281 people found this instruction helpful
Opened the microwave door and put the new plate on the carousel. Duh!

the cooking tray went crash!

  • Customer: lisa from monroe township nj NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 141 of 280 people found this instruction helpful
I ordered on tuesday right before Thanksgiving and was sick my tray plate broke with a house full of company comming for the holiday and no microwave low and behold i ordered on tuesday and it was at my door on wednesday what a shock i will forever be a loyal customer thanks part select!!!

The door handle broke and required replacement.

  • Customer: Michael from Gloucester VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 72 of 74 people found this instruction helpful
The handle is attached with two screws. The top screw is located on the inside of the door and is visible and unobstructed. The bottom screw however, is not visible, but is almost directly below the top screw. It is located behind a 1/2 inch wide plastic retainer that runs around the inside of the door. Simply pry the retainer from the inside of the door enough to access the screw. This would be the lower left corner of the retainer when looking at it from the inside of the door. I used a kitchen knife to pry the retainer loose and a phillips screw driver to remove the screws. The process is simple and takes about five minutes.

Broken Cooking Tray

  • Customer: Berney from Madison AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 139 of 278 people found this instruction helpful
Just placed the new tray in the microwave. Simple as that.

broke the glass cooking tray in my microwave

  • Customer: Cynthia from Chapel Hill NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 139 of 279 people found this instruction helpful
It was easy. went to GE website and click onto parts replacement. Placed my order and within three business days the new glass tray arrived. How easy was that....
All Instructions for the JVM1350WW02
1-15 of 233