Models > JVM1340WW02 > Instructions

JVM1340WW02 General Electric Microwave - Instructions

All installation instructions for JVM1340WW02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JVM1340WW02
61-75 of 233
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Cooktop light receptacle cracked

  • Customer: Ronald from Wood Dale IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Remove screws holding bottom cover. Cover then swings down allowing access to the receptacles. Receptacles have a single screw attaching them to the appliance with a simple electrical plug supplying power. Very easy.

turntable not turning

  • Customer: randy from navarre FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 5 people found this instruction helpful
after dealing with the turntable in my microwave not turning for a couple years i decided it was time to fix it.Checked it out and found the turntable motor bad.I looked on line for pricing and availability,ordered the part from partselect.Two days later the part was at my door.Thirty minutes, a few screws and a couple spade connectors later, my microwave was working like brand new.Making myself and more impotantly my wife real happy.It was a very easy repair,next time I won't wait so long!

Broken glass and bad bulb

  • Customer: Chris from Destin FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Removed one screw, slid frame out and removed broken glass. replaced bulb. The hard part was slidding the frame back in place and starting the screw. We were very surprised at the fast delivery of the parts, thank you. The sad part, a few days later the glass broke again. We are trying to get to the people at GE to solve our problem. We feel like that will not happen, we just do not have the time to stay on hold on the phone waiting for someone to solve our problem. Will reorder glass.

Micrwave won't run - turntable turns backwards when door opened...

  • Customer: Roger from Fountain Hills AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 2 people found this instruction helpful
Most of the effort is simply getting the oven out of the built in enclosure and the sheet metal off. This take about 15 minutes then you have to remove the two screws (not handy location) that hold the door latch/switch assembly so you can remove the switch. I did this BEFORE ordering so I could test the switch (it was charred) and verify the part needed. WATCH OUT - some ovens use a normally open an some a normally closed version of this switch - you have to get the right one. I checked several suppliers that were showing the WRONG switch for my model. PartSelect had it right. Once I received the switch I had it on and the oven installed and running in less than 30 miutes. Working fine since then...

Microwave wouldn't start after "Start" pushed

  • Customer: Don from Monte Sereno CA
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
Took cover off, noted the two side by side switches easily visible and we hought one of these was responsible. Then son noted a third switch at the top of the plastic assembly which inserts at an odd angle. When it was inspected signs of a previous short showed up with burnt contact points. Reinserted at same odd angle as there were guide holes, closed things up and oven worked 100%. Great prompt service and great website!! We will use you again

Bulb burned ot

  • Customer: John from Fort Smith AR
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 2 people found this instruction helpful
Un screwed the cover but when i tried to remove the bulb it was broken at the base. I disconnected the power and used neddle nosed pliers to remove the base

Replace door handle

  • Customer: Herve from Ashburn VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
THere are two screws holding the door handle. One is easliy accessed, the other is hidden.

There is a plastice seal that needs to be removed from inside the door. Its about 1/3 of an inch wide and is on the inside of the door surrounding the glass. It is NOT on the jam but on the inside surface of the door itself. You need thin tool to begin to pry out the seal. Once the first section is loose the rest comes out easily.
The hidden screw is easily accessible once the seal is out.
Simply pop back in when done.

Light bulbs wouldn't come out of socket

  • Customer: Toni from Denton NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
I ended up breaking one bulb trying to remove a burnt bulb for replacement. We then tried removing the other bulb and it wouldn't come out either. I googled the problem and found PartSelect and an explaination of the problem. Heat from either the stove or the bulbs had fused the bulbs into the sockets. Comments on the problem explained that you just remove the bottome pannel (we had seven screws), unplug the old sockets, insert the new and new bulbs and reattach the panel. It was quick and no problems to correct. We did discover the microwave was on its own breaker, make sure to disconnect or cutoff power to the microwave before you start.

After 12 years my handle cracked upon opening microwave.

  • Customer: Lori from Spring Hill FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
I unscrewed the top inside screw, pried the inner plate off with a butter knife revealing the bottom screw. Replaced handle, screws and plate. It was so easy for me because I read about it on your website. Otherwise, I had no clue!

microwave would not start

  • Customer: JULIA from JACKSONVILLE FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 6 people found this instruction helpful
took of cover removed switch and replaced with new one

Bent, Broken, Melted rack support

  • Customer: JAMES from PISGAH FOREST NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
Ordered new support (price was less than Postage) Ordered for Microwave, should have ordered for Convection Microwave. Filed side SS to fit part ordered, after much filing got the new part (wrong) into the side panel. Looks great, wrong color but should be OK/

One support always fell out/ other was fried to the wall

  • Customer: Philip from Forest Hills Gdns. NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
Because of it's age and my memory of it's wall installation problems, I was extremely happy to find the parts. Merely popped the old "fried " support bracket out, snapped it the two replacement brackets and I was back in business with a "new" spark free appliance. Thanks ever so much! Smooth, "no brainer" installation! Extremely pleased with results!

Door handle broke off of microwave

  • Customer: ashley from roswell GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
There were only two screws holding the door handle in place. The first is obvious but the second requires that you snap off the plastic window cover on the door. I only took it partially off using a butter knife to lift it. It snaps out easily.
Take out both screws which removes all parts of the old handle. Then just put in the new handle and use old screws to secure it in place. Except for removing the plastic cover, this was absolutely trivial.
$60 seems expensive for a plastic door handle, but it is cheaper than a new unit.

Original door handle broke off

  • Customer: widmark from wellington FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
I read some of the previous blogs on same problem. Followed same steps others took before me and I was done in 5 minutes! Opened the microwave door. Removed the top screw that was visible and then removed the ring around inside door frame by using a simple butter knife to get it going carefully. Removed the hidden screw on bottom of door . Replaced Handle, screwed in top and bottom , attached plastic seal around door by snapping it back in place. Done

Power worked but would not cook

  • Customer: Jim from Albuquerque NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Took the front panel off, played with the switch while it was plugged in to verify the switch was bad. I actually was able to tweak the switch just right to keep the microwave working while the part was being delivered. When it came it was just removing two small screws and replacing. Very easy.
All Instructions for the JVM1340WW02
61-75 of 233