Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JVM1339WW02 > Instructions

JVM1339WW02 General Electric Microwave - Instructions

All installation instructions for JVM1339WW02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JVM1339WW02
31-45 of 231
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

repair broken lens and replace light bulb.

  • Customer: Heidi from Astoria, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 18 of 25 people found this instruction helpful
This was a super easy repair job. I couldn't figure out how the lens that covered the light bulb would have cracked and realized it must have been from my contractor when he replaced my stove. I can't prove it, of course, so I am left doing the repairs. The website was very easy to order from and confirm that I had the correct parts as the model numbers tend to change over time.

Broken door latch

  • Customer: Tim from White Bear Lake, MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 17 of 23 people found this instruction helpful
First, I removed the screws that hold the handle to the door, and then removed the handle. Then, I used a small flathead screwdriver to pry the door apart. Then I slid out the front glass panel, and exposed the side of the door. The replacement piece was easy to install, it is just held in with two pins and a spring.

Changing the bulb that illuminates the cooktop

  • Customer: LUCY from BALLWIN, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 18 of 27 people found this instruction helpful
Loosen screw holding glass cover plate in place over bulb. Glass cover plate will swing down. Unscrew bad bulb, replace with good bulb, reset glass cover and tighten screw.

Light bulbs wouldn't come out of socket

  • Customer: Toni from Denton, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 13 of 14 people found this instruction helpful
I ended up breaking one bulb trying to remove a burnt bulb for replacement. We then tried removing the other bulb and it wouldn't come out either. I googled the problem and found PartSelect and an explaination of the problem. Heat from either the stove or the bulbs had fused the bulbs into the sockets. Comments on the problem explained that you just remove the bottome pannel (we had seven screws), unplug the old sockets, insert the new and new bulbs and reattach the panel. It was quick and no problems to correct. We did discover the microwave was on its own breaker, make sure to disconnect or cutoff power to the microwave before you start.

Broke light fixture socket

  • Customer: Norman from Benson, NC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 10 people found this instruction helpful
Rather than open access door took off bottom (5 screws) This gave more room as the microwave is mounted under the wall cabinets over the stove.

Burned out fuse and burned out bulb

  • Customer: Richard from Galva, KS
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 14 of 23 people found this instruction helpful
Put radioactive nuke suit on. Unplug microwave, used philips screw driver and took glass plate from the bulb cover, unscrew burnt bulb and replace with new bulb. Put cover back over replacement bulb, insert screw and tighten. Then used philips screw driver to take two screws that held the front control panel in place, then it folded down, then checked 20 amp fuse, it was burnt, replaced it with a new one. Folded control panel, inserted two small philip head screws back into control panel. Then plugged microwave back in, set the clock, tested it with cup water. Worked like a brand new one. Take off radioactive nuke suit. Just kidding about the radioactive nuke suit.

Broken light lens for the light bulbs

  • Customer: TERRELL from OAK POINT, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 11 of 15 people found this instruction helpful
Took the screw out of the glass door holder, bent the clips up and removed the broken glass. While this was open chenged the light bulbs as well. Put new glass in bent the holding clips down and closed the doors and installed the screws again. So nice to have good light again and also new glass in them. Never noticed they were broken before.

BY THE WAY PARTS SELECT IS VERY PROMPT AND I RECEIVED MY PARTS IN ONE DAY AFTER THEY SHIPPED. SHIPPED ON MONDAY GOT THEM TUESDAY, thanks parts select for your promtness and speedy work for shipment.

Light socket replacement

  • Customer: lester from orlando, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 9 people found this instruction helpful
I unscrewed the entire undersurface of the microwave (I didn't do this before!) and replaced the light socket. Easy job and I'm glad the part was still available.

Microwave would not go on

  • Customer: Jim from Lincolnshire, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 14 of 26 people found this instruction helpful
All electrical worked (fan, lights, control panel) door switch was broke. Pulled the oven out. Took out two big screws from the cabinet above. (be careful not to drop oven)Set the oven on kitchen counter. Took off five screws that held the vent cover. Removed vent cover. Took out one screw that held the control panel. Lifted, turned and slid the panel into the space below so I could get to the upper door switch. Replace door switch and re-assemble.

Replace microwave light and broken base socket

  • Customer: Jerry from Pearland, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 9 people found this instruction helpful
Lower base of the microwave, about 6 screws,
replaced broken light bulb socket,then re-installed.
Installed new light bulb.

When opening door, the microwave would turn on

  • Customer: William from Fridley, MN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 9 people found this instruction helpful
I've been fixing and taking things apart since I was a kid. I hoped that it was a bad switch in the door. Got out my test meter and check the 3 different switches. All 3 tested good, but one was a bit hit and miss. It would work if the microwave was on its side and wouldn't when it was set flat. I found the switch online and installed it. Took care of the problem.It was a whole lot cheaper than buying a new microwave. Thanks! Bill Brown, Fridley, MN

Oven blows 20 amp fuse

  • Customer: PATRICK from Covington, LA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 12 people found this instruction helpful
Primary door switch was shorted and blew the fuse when the oven was plugged in. Replaced primary door interlock switch.

Bulbs broke off in socket, socket would not come out

  • Customer: William from Kingwood, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 8 of 10 people found this instruction helpful
I removed both sockets from the microwave and when your part arrived, I installed them both including the new lights. The work perfectly and it was very easy to put them in. I also appreciate the speed of delivery and your concern for my feed back on the product. I have you number in my contact list and should I need another part, I'll check with your first.
thanks you

dirty, needed to be replaced

  • Customer: Brenda from Iowa City, IA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 15 of 31 people found this instruction helpful
I was very happy with the ease of finding the product I needed, the time it took to arrive and the fact that I received the right part. The replacement process was easy and only took about a minute.

broken lens

  • Customer: greg from bellingham, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 7 people found this instruction helpful
first i remove the screw, then removed the lens assembly (really a frame) bent the feet out of the way, slid the old lens out and the new one in, bent the feet back in place and inserted the assembly into place replaced screw. the killer is a day later it was broken again, think the lens can't handle the heat from the oven below or the lights above. you guys where great fast and exact match part but the ge design is flawed
All Instructions for the JVM1339WW02
31-45 of 231