Models > JVM1339WW02 > Instructions

JVM1339WW02 General Electric Microwave - Instructions

All installation instructions for JVM1339WW02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JVM1339WW02
181-195 of 230
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Operates but does not heat

  • Customer: Marvin from Page AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Found blowup drawings inside unit, which helped identify what I had to remove. Had neighbor assist in lifting unit from wall mount, unit slides easily from rails once top bolts are removed. Pay attention to where all the screws go as you remove them, some inside assemblies will have to be removed or loosened. A good guideline to go by is all black screws hold internal assemblies, the bronze screws go in the back side and the chrome screws go on top, sides, and front of the unit. I was able to lift unit back on rails without any assistance.

Unit would not come on.

  • Customer: Phillip from Umatilla FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed access panal, found soft switch as discribed on your web site. removed and replaced.

Broken plate in microwave

  • Customer: Patrick from Charlotte NC
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I slipped the new saucer out of the box and placed it in the microwave. I was very disappointed to discover that the new one didn't fly like the old one.

the door handle on my GE microwave broke.

  • Customer: David from madison MS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
One screw is exposed and the other lies beneth a plastic trim. The trim was easily pried off with a screw driver and the handle replaced. I reused the existing screws. If you need some order them because they don't come with the handle.

Glass cover for Light Bulb was cracked..

  • Customer: Donna from Denver CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
It was great...Thank you for having the part available...

Handle broke off door

  • Customer: Charlene from Ellenton FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed old handle and replaced it with new one very easy but I thought very expensive

no lights

  • Customer: DON from CHEHALIS WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Remove light cover. Replace bulbs Note. Light bulbs are 40W,Too much heat for bulbs & sockets

OVER STOVE LIGHT BULB OUT

  • Customer: DALE from ST PETERSBURG FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
TOOK SCREW HOLDING LENS COVER OUT, DROPPED COVER DOWN, UNSCREWED OLD BULB, SCREWED NEW BULB IN SOCKET. SCREWED COVER BACK IN PLACE. THIS IS THE THIRD BULB IN THIS SOCKET, THE OTHER BULB IS ORIGINAL.

Door handle broke

  • Customer: Janis from Arlington VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
This is the second time the handle broke, so I learned from the first time -- although it was more than 10 years ago since the last repair. To familiarize myself, I checked out Youtube videos about replacing this part. I learned that I needed to pry off the frame on the inside of the door -- which was easy -- and I onlly had to pry it off about 3/4 of the way in order to access the bottom screw of the handle. The top screw is accessible without having to pry off the frame. Easy DIY project.

handle cracked

  • Customer: LINDA from NORTH OLMSTED OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove top screw.Remove seal on inside around glass which lets you get at bottom screw.Unscrew bottom screw in handle. Put on new handle and screw it in firm only. Replace seal around glass. Done

Light bulb burned out

  • Customer: Bob from La Crescenta CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Easy as can be. Removed one screw on the glass cover, removed two burned out bulbs and reinstalled two new bulbs, reinstalled the cover and all is well now. The best part - my 'supervisor' is happy that she can see to cook again!

Microwave light bulbs went out

  • Customer: Barbara from Wixom MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Because the microwave is old and the bulbs, I believe, had never been changed I carefully tried to unscrew the bulb. However, when I went to unscrew the bulbs the end of the bulb broke off and remained in the socket. I used a few different tools then remembered that sometimes a raw potatoe can be used to unscrew the remainder of the bulb, but to no avail. Finally had to unscrew the whole underside of the microwave to remove the broken bulb. May I suggest that you have the socket face away from the wall to screw in the bulb instead of the socket pointing toward the wall. You need to know yoga just to manuver the bulb into the socket.

Microwave came on when door open

  • Customer: Barry from Navarre FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Turn off main power bracker. Removed fan vent, removed control panel, disconnect leads to the three monitor switches. Replaced the secondary switch (top). Reversed procedures.

Light bulbs in the night lights kept blowing out

  • Customer: Anne from Allen Park MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed 5 screws from the bottom of the over the range microwave to expose the light sockets. Removed the 1 screw holding the socket, disconnected the wires. Attached the wires to the new socket, Put in the bulb, reattached it with the screw. Repeated on the other light... It took about 20 minutes and now the lights work just like they should :)

glass light lens, light bulb, bulb socket

  • Customer: Leo from Canton TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The order was easy and promptly received. I lowered the cover by removing retainer screws underneath. Simply lowered it and removed the broken glass and replaced it. The bulb was broken and the base of it was stuck in the socket. I didn't bother to remove it because the socket was brittle. I disconnected the socket by unplugging the wires, removing the retainer screws,and removing it. I replaced it with the new one. Screwed in the bulb. I replaced the cover and it was done. Ps: I used an Hitachi cordless screwdriver, which greatly helped when doing this alone.
All Instructions for the JVM1339WW02
181-195 of 230