Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JVM1339BW02 > Instructions

JVM1339BW02 General Electric Microwave - Instructions

All installation instructions for JVM1339BW02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JVM1339BW02
106-120 of 204
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken lens.

  • Customer: Gary from Warren, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Used a phillips head screw driver and loosened the lens frame under the microwave. Removed the broken lens and replaced it with the lens ordered. Put the lens frame back in place and secured it with the phillips head screw.

Door handle broke off

  • Customer: Douglas from Angola, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
I first pulled the bottom left and left side inner 3/8th inch rounded liner out. Use a thin flat head screw driver to gently pry the inner trim piece out of place. This exposed the bottom screw. I pulled out the old 1/2 inch silver coarse thread screw. The top screw is obvious. Removed that. I had to replace the face plate which slid off. Replaced the new face plate then put in the new handle top male end then the bottom male end in the holes. I screwed in the top 1.5 inch browm fine thread screw. Don't over tighten, just go until snug. If you over tighten you may crack the plastic walls of the screw hole built into the handle. I then put the small screw in and tightened it. Then snap the trim piece back in place. Viola.......You are done

Handle broke off, bulb burned out the broke trying to get it out.

  • Customer: Douglas from Angola, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Once on your web site it gave me a skematic of my microwave which showed me how the parts connected. I saw how easy it was and I saw what type of bulb it was I ordered the parts and it took less than 15 minutes to repair. Thank you so much for your site, It is now on my favorites list. Doug

the handle broke off.

  • Customer: D Katherine from Pittsfield, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
ordered the handle it was so easy to installed with help fron do it yourselfers.thanks

light out over stove

  • Customer: virginia from hilton head island, SC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
so easy, but how do i turn light off?

Part recieved next day. thanks so much

Underneath Light On Microwave Would Not Come On.

  • Customer: MARY from PLYMOUTH, MA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
My son=law did repair because I am elderly and it was necesary to remove the bottom plate of the microwave which I was unable to do. The microwave was installed in 1987 and I believe this was the first time to replace the bulbs. When my son removed them the bulb was diintergrated. That's how old they were. Once he was able to remove the underneath plate the repair was easy except for removing the old bulbs. I think that I could have done it myself but he was available and I am sure it was done much better. All in all the parts)bulbs) were correct and everything is workiin fine. This is a good place to order replacement parts. In fact I am going to order a new charcoal filter. He took the label off the old one and I am ordering the replacement. After all 1987 may have been a good year, but time for a new one. Mary

Many months agoI replaced a bulb in the light and it did not work. After swapping bulbs with the light on the other side I determined it was not the bulb.

  • Customer: Thomas from Rochester, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 4 people found this instruction helpful
I asked a handyman at the local fitness center about repairing it and he refered me to your website where I found an exploaded drawing showing the parts I needed and how to get to them. It was great and very easy.

Old handle broke off of the microwave

  • Customer: Susan from Granbury, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
We planned on buying a new microwave but thought well, we would see if there was a part available for a 13 year old microwave. Lo and Behold! Partselect.com had one! It was shipped and we got it in a couple of days. By reading what others (professional installers) said about putting the new handle on, I was confident to let my husband tackle this on his own! We saved a service call and now it works like new!! Thanks

Microwave door handle was broken.

  • Customer: Gary from Mountain View, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Used thin spatula to remove plastic frame around inside of door to expose bottom screw. Removed top and bottom screw and pulled off broken handle. After cleaning up the outside of the door, installed new handle and tightened screws. Popped plastic frame back into place: done!

Handle broke

  • Customer: Donna from Fontana, CA
  • Difficulty: Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
My son repaired it. The difficulty was because there was no schematic included and we couldn't figure out how to access the screw at the bottom of the handle. My son downloaded a schematic from the internet and finally figured out how to do it from that, but it would have been a lot quicker and easier if one had been included with the part. I was very satisfied, however, with the speed of the delivery.

Turntable problem.

  • Customer: Timothy from Hillsborough, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 4 people found this instruction helpful
Removed broken coulper.Snaped new coulping in placed.job done.

Light bulb was burnt out and lens was broken

  • Customer: Andrew from Bolton, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Unscrewed the lens, it hinged down, then I could remove the frame. Pulled old bulb out and replaced with new one. Replaced broken glass in frame. Reset hinge into the holes and swung it up into place. Screwed it in.

Very easy!

Microwave door handle broke at bottom

  • Customer: Jan from Sparks, NV
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Followed the instructions from the do-it-yourselfers on your web site which were all excellent and a wonderful asset to your site. It took us much longer than 5 minutes (about 20 min.) because we couldn't get the bottom screw out and then had one heck of a time screwing it into the new handle. Don't know if the srew was too long, too big or what, but we feel confident that it won't fall out!

Broken Handle

  • Customer: David from Norristown, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
2 screws out 2 screws back piece of cake

Broken Handle

  • Customer: JOSEPH from NEDERLAND, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Replaced - unscrewed top screw, removed door gasket with spatula, reveiling bottom screw to unscrew. Replaced handle,screw back on and replaced door gasket. Follow instruction on web site. Help greatly
All Instructions for the JVM1339BW02
106-120 of 204