Models > JVM1339BW02 > Instructions

JVM1339BW02 General Electric Microwave - Instructions

All installation instructions for JVM1339BW02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JVM1339BW02
46-60 of 204
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Microwave handle broke

  • Customer: Rosemary from Roseville, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
First mistake I made was assuming the replacement handle would come with screws. It didn't so had to place a second order for the top screw. Make sure you order everything you need. First I popped off small rim on inside of door with the tip of a knife to expose the lower screw. Removed old handle. Set new handle inplace and tightened both top and bottom screw. Replaced rim to original position. And voila! Done. Easy fix if you have all the necessary parts.

Replace microwave light and broken base socket

  • Customer: Jerry from Pearland, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
Lower base of the microwave, about 6 screws,
replaced broken light bulb socket,then re-installed.
Installed new light bulb.

Sparked at the coupler, burnt

  • Customer: Robert from Bakersfield, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
Using the exploded parts view I removed three Philips screws from the lower plate (the screws are located on the front edge of the panel that holds the air filters). Slide the lower panel forward slightly and allow it to swing down. Remove the amphenol connector to the motor and hood lights by pressing the sides of the plastic clip and place the lower panel to one side out of the way. f you intend to clean the lower panel in a dishwasher remove all electrical components before doing so (bend back the clips holding the wires in place and remove the lamps, remove the Philips screws holding the lamp holders); note: these are the only screws with a short shoulder on them, make sure they go back in the same place to hold the lamp holder to prevent damage to the holder). Remove the Philips screw holding the turn table motor in place. Slide the entire motor assembly to one side to allow the motor shaft to slide off the coupler. With the oven door open, remove the old coupling by sliding it to one side to clear the retainer. Insert the new coupling and replace the motor making sure you align the motor shaft with the flat side of the coupling. If you have cleaned the lower assembly in the dishwasher or by hand make sure all parts are dry before reassembly (reinstall the lamp holders and the wiring assembly. Reconnect the amphenol connector (it can only plug in one way by nature of design). Slide the back of the lower assembly into the channel at the back of the oven and replace the three screws holding the lower panel in place.
Now you have saved your self the cost of a service call or possibly a new microwave you can use this as supporting evidence that you can afford the new 20" monitor for your PC. Test out the repair and make your spouse a cup of hot coffee or cocoa to brag on yourself and make your sales pitch.

Plastic door handle broke off

  • Customer: Michael from Alexandria, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
I ran into the same problem everyone does when doing this job. I found and removed the top screw from the back of the door but could not see the bottom screw so was unsure how to remove old broken plastic piece from lower handle attachment point and reinstall new. I went back to the website and found the comments from others re how to do this and from there it was a 2 minute job. The only thing I would add is a caution: When removing the wide black plastic flange from inside the door (to access the bottom screw) pry it out carefully all around. If you pry open only at the handle end and start pulling away there is a risk of snapping the flange

The bottom screw holding the handle to the door broke off.

  • Customer: Phillip from Lawton, OK
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
First I remove d the top screw which can be seen when the door is open. Next I gently pried the plastic rim away from the inside of the door which uncovered the bottom screw.
Placed the new handle in position and reversed the removal process, carefully tightening the screw, being careful to not overtighten. Snapped the plastic rim back into place and the job was done.
The whole repair took less than 5 minutes! I saved big bucks by doing it myself and it is not difficult as long as you can operate a screwdriver!

Bulbs broke off in socket, socket would not come out

  • Customer: William from Kingwood, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 7 people found this instruction helpful
I removed both sockets from the microwave and when your part arrived, I installed them both including the new lights. The work perfectly and it was very easy to put them in. I also appreciate the speed of delivery and your concern for my feed back on the product. I have you number in my contact list and should I need another part, I'll check with your first.
thanks you

Loss of lighting for over-stove illumination.

  • Customer: ROGER from BLUFFTON, SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
Must remove 5 screws in bottom of Microwave, which is hinged to the unit. Then simply remove the old lamp holders, and replace with replacements. Uses only a single screw for each lamp.

Light Socket replacement

  • Customer: Jill from Arlington, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
I was told by 2 different appliance technicians that the crumbled/melted light socket could not be replaced which meant replacing the entire microwave (expensive!). Other posters on your sight described the repair steps and I gave it a try. The hardest part was probably figuring out which switch in the fuse box belonged to it (now marked clearly). It was a simple matter of unscrewing the bottom panel of the microwave to access the socket, pulling the crumbled/melted unit off and shoving the new one on. I can't believe the repairmen didn't want any part of even giving it a try.

Bulb was stuck in the lamp

  • Customer: lawrence from huntersville, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 3 people found this instruction helpful
First I removed the screws that were underneath the microwave. Once I did that I disconnected the wires to the bulbs and removed the screws that were attached to the holder lamp. replaced the parts and reversed the process. It went really smooth.

Door handle broke off at bottom.

  • Customer: Anita from Umatilla, OR
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
Took the microwave door off. Then read other repair stories here online and discovered that wasn't neccesary. So when the handle arrived I only had to unscrew the top visible screw, pry the bottom plastic strip off the door to reveal and remove the hidden screw. From there it was only a matter of seconds to attach the new handle and snap the plastic strip back in place. Only thing I need to mention is we did not realize the part would be coming from Canada and were surprised to see the additional postage fee charged to our debit card. Felt that should have been added up front. Not a problem, just a surprise.

Broken glass and bad bulb

  • Customer: Chris from Destin, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
Removed one screw, slid frame out and removed broken glass. replaced bulb. The hard part was slidding the frame back in place and starting the screw. We were very surprised at the fast delivery of the parts, thank you. The sad part, a few days later the glass broke again. We are trying to get to the people at GE to solve our problem. We feel like that will not happen, we just do not have the time to stay on hold on the phone waiting for someone to solve our problem. Will reorder glass.

Handle on the Microwave broke

  • Customer: Michael from Woodbridge, VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
The Parts select diagram and order ing process made it very easy to complete my repair job. After receiving my parts, I unscrewed the screws with a phillips driver. Then I popped out the handle. There is one tricky part - the screw is a bit too small for the existing whole and so I added a washer to fix this problem. I then slide in the new handle. Very easy!

Power worked but would not cook

  • Customer: Jim from Albuquerque, NM
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Took the front panel off, played with the switch while it was plugged in to verify the switch was bad. I actually was able to tweak the switch just right to keep the microwave working while the part was being delivered. When it came it was just removing two small screws and replacing. Very easy.

Microwave would turn on when door opened

  • Customer: Lois from El Segundo, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 7 people found this instruction helpful
Unscrewed numerous screws holding the "body/shell" to the microwave. Removed body. I then unplugged top door switch, replaced it with new one, and "tested" the new one. I fixed our $400 convection micro with an $18 switch. NICE!

Lens Was Not Sized To Fit And Was Left Extremely Sharp

  • Customer: robert from salmon, ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Had to take to a local glass shop for sizing and to remove sharp edges. Will never order again.
All Instructions for the JVM1339BW02
46-60 of 204