Models > JVM1339BW02 > Instructions

JVM1339BW02 General Electric Microwave - Instructions

All installation instructions for JVM1339BW02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JVM1339BW02
151-165 of 203
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken plate in microwave

  • Customer: Patrick from Charlotte NC
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I slipped the new saucer out of the box and placed it in the microwave. I was very disappointed to discover that the new one didn't fly like the old one.

Glass cover for Light Bulb was cracked..

  • Customer: Donna from Denver CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
It was great...Thank you for having the part available...

The handle on my microwave oven broke and had to be replaced.

  • Customer: Diane from Homer Glen IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The repair was easy. First, I read what a gentleman wrote about replacing the handle on his microwave and I followed what he did. I removed a screw, then the stripping around the inside glass, and then I removed the second screw. Hold the handle to the outside of the door, screw in the screws, then snap in place the stripping. It took the gentleman two minutes to replace his handle but it took me longer cause I couldn't get the bottom screw in place. My total time was under 10 minutes.

no lights

  • Customer: DON from CHEHALIS WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Remove light cover. Replace bulbs Note. Light bulbs are 40W,Too much heat for bulbs & sockets

OVER STOVE LIGHT BULB OUT

  • Customer: DALE from ST PETERSBURG FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
TOOK SCREW HOLDING LENS COVER OUT, DROPPED COVER DOWN, UNSCREWED OLD BULB, SCREWED NEW BULB IN SOCKET. SCREWED COVER BACK IN PLACE. THIS IS THE THIRD BULB IN THIS SOCKET, THE OTHER BULB IS ORIGINAL.

Light bulb burned out

  • Customer: Bob from La Crescenta CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Easy as can be. Removed one screw on the glass cover, removed two burned out bulbs and reinstalled two new bulbs, reinstalled the cover and all is well now. The best part - my 'supervisor' is happy that she can see to cook again!

Microwave light bulbs went out

  • Customer: Barbara from Wixom MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Because the microwave is old and the bulbs, I believe, had never been changed I carefully tried to unscrew the bulb. However, when I went to unscrew the bulbs the end of the bulb broke off and remained in the socket. I used a few different tools then remembered that sometimes a raw potatoe can be used to unscrew the remainder of the bulb, but to no avail. Finally had to unscrew the whole underside of the microwave to remove the broken bulb. May I suggest that you have the socket face away from the wall to screw in the bulb instead of the socket pointing toward the wall. You need to know yoga just to manuver the bulb into the socket.

Microwave came on when door open

  • Customer: Barry from Navarre FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Turn off main power bracker. Removed fan vent, removed control panel, disconnect leads to the three monitor switches. Replaced the secondary switch (top). Reversed procedures.

Light bulbs in the night lights kept blowing out

  • Customer: Anne from Allen Park MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed 5 screws from the bottom of the over the range microwave to expose the light sockets. Removed the 1 screw holding the socket, disconnected the wires. Attached the wires to the new socket, Put in the bulb, reattached it with the screw. Repeated on the other light... It took about 20 minutes and now the lights work just like they should :)

glass light lens, light bulb, bulb socket

  • Customer: Leo from Canton TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The order was easy and promptly received. I lowered the cover by removing retainer screws underneath. Simply lowered it and removed the broken glass and replaced it. The bulb was broken and the base of it was stuck in the socket. I didn't bother to remove it because the socket was brittle. I disconnected the socket by unplugging the wires, removing the retainer screws,and removing it. I replaced it with the new one. Screwed in the bulb. I replaced the cover and it was done. Ps: I used an Hitachi cordless screwdriver, which greatly helped when doing this alone.

Broke glass plate cooking tray in microwave

  • Customer: Jan from Los Gatos CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
New part came -- perfect fit, set it in the microwave, no problem.

would not turn on - plug in and would shut off right away

  • Customer: Vita from Flagstaff AZ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
thank you very much.

Bulb Light Replacement

  • Customer: James from Walpole MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I thought I could just unscrew the bulbs in the SpacemakerXL Microwave Oven. The bulbs melted into the bulb socket so every attempt to unscrew the bulb with pliers just broke the socket. So I took out the few screws holding up the bottom panel(with the bulbs and filters). I unplugged the electrical connection and took out the sockets but I used PAM Cooking oil on the electrical connections plugging into the sockets to avoid pulling the wire holders from the connection. Replacing both bulbs and the sockets at the same time makes sense since the heat from the stove melts the bulbs in the socket.

burnt out bulb /microwave

  • Customer: gerri from north haven CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
simply to install new bulb. Unscrewed the under the microwave lamp door with a screwdriver. Inserted new bulb into socket. good to go

microwave will not come on

  • Customer: Martha from Anaheim CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I replaced the cover just fine but i think a sensor went bad
All Instructions for the JVM1339BW02
151-165 of 203