Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven was not coming up to temperature
I had to remove the oven from the wall because the sensor plug connction is behind the unit. Two screws hold the sensor inside the oven and then I disconnected the lead and pulled the sensor out from the front. I installed the new sensor, tightened the two screws holding it in and connected the lead. Then reinstalled the oven into the wall. Overall, a very easy repair once you get the oven out.
Removed the oven door for easy acces to oven. Unscrewed (philips screwdriver) the screw holding temp sensor in place. Gently pulled the wiring until quick connector was located. Pushed down on locking level on quick connect while holding other end of wiring (so wiring would not fall back behind oven). Connected the new sensor and screwed back in place. Reinstalled oven door. Tested temperature settings by turning on oven and comparing with a separate oven thermometer.
It was much easier than trying to remove the bonded aluminum foil from the false bottom/drip pan. Simply lift and remove oven front door, (see your manual), slide out false bottom and slide in new. For me it did take longer than 15 minutes, but that's because I was doing a thorough oven cleaning. The part was in the $50 range and well worth it. Why didn't anyone ever tell me that you can no longer line the bottom of your oven with aluminum foil?
Seal worn on corner allowing heat to escape, sensor not reading the correct temperature
Spring clips installed on seal just pull off door. New clips get inserted in mounting holes and are pushed in to seat in door. Seal ends slide into door holes.
Replaced old sensor with new one by removing nut screw and carefully pulling sensor cable out of oven back until plastic terminal connection is exposed. Sensor connection has a locking tab that must be pushed in to release sensor connector. Do not allow oven wire to pull back into back of oven until new sensor is connected. Reinstall nut screw and tight to hold new sensor in place. Verify proper oven operation.
After turning the breaker off, using a 1/4 inch nut driver I removed all the clamp screws (5) holding the heating element in place. I then unplugged the element wire spades from the rear of oven and removed the old element. Installing the new one was simply going in reverse order. After plugging the new one in, I did however, use plyers to squeeze the connectors and make the connections tighter. It took a little more back work than I thought because I was leaning over most the time. All in all, I saved a hundred dollar bill in doing this 30 min job myself.
Something in oven exploded and stained glass so couldn’t see what’s baking
Ordered window pack from PartSelect then removed oven door from front of stove, then removed back of door and silver backing and glass pack. Dropped new glass into place. Replaced all backing,put door back onto stove. Tip. When removing screw keep them separated from each other as not to get mixed up when putting everything together. Good Luck, PartSelect has all the parts you need, this my second getting a part from them.
After reviewing the potential causes for the error code, I decided I'd try to change out the temp sensor. Using the ohmeter, I saw the difference immediately between the old and new sensor. The sensor is accessed from the back of the stove, and must be slide out to gain access to the rear panel. Since the stove I have is a built in, removing the stove and the access panel was the hardest part of this repair. Resetting the glass control panel was also a bit tricky to calibrate the touch sensitive buttons. Good luck.
lift door off and remove racks take out old sensor. one word of advise when pulling old sensor out tie a string around connector coming out of oven if it slips out of yor hand it could fall through hole iif you dont have a string attached you pull the whole oven out of wall to acess it
When we bought the house the gasket was hard from food deposits
Just pulled out the old one and pushed in the new one. Very easy. I was afraid to run this self-cleaning oven until I installed the new gasket. It worked perfectly.
I unfastened the three 1/4" rear screws, then the two support screws on top. I pulled the old element out,( plenty of slack wire luckily). disconnected it from the bayonet-type connections, then attached the new element. I secured the new element using the 1/4" screws. Bingo!
Disconnect the power to the oven at the main breaker panel. Open the oven door to the first stop (not all the way open) and pull straight up to remove the oven door from the hinge. Using a 1/4" drive ratchet with 1/2" extension with 1/4" socket, remove the 1/4" sheetmetal screw holding the temperature probe at the center of the broiler mounting plate. Remove the two 1/4" screws holding the broiler mounting plate. Remove the two 1/4" screws holding the broiler element at the ceiling of the oven. Pull the broiler element out from the back of the oven and there should be two electrical connectors at the back of the broiler element. Pull the electrical connectors off of element. Replace the element and re-install in reverse order.
Very simple. Remove one screw and carefully pull the sensor until you see the connection point. Remove the old one and snap the new one in and guide the wire back and reassemble the screw. Be sure to remove the oven door for easy access.
had to remove the oven from the wall. once i realized that i had to take the side wall brackets off before removing the oven it was quite easy. then just had to remove oven door and slide the unit onto a chair while replacing the sensor. put it all back in and the wife was so happy to have her oven back she made me a batch of brownies. yum.
Just like everyone else it was a simple r&r. However, when removing or installing wire clips I make it a habit to hold the ends with needle nose to prevent any: "snap!" ooops! However to prevent burning the element in the first place, it is strongly suggested to push that broil button twice so that it is set to low temp. It is too easy to use the high setting which will shorten the elements life by 40 - 60 %. Also, keep the oven door partially open when using the broiler. Like the manual tells you!!!