Models > JRSD224L (7N07A)

JRSD224L (7N07A) Jenn-Air Refrigerator - Overview

Get Parts and Repair Help for JRSD224L

If you know the refrigerator repair part you need, you can browse the list of all parts on the JRSD224L, or you can search by name or part description. You can also find your part by where it is located on the JRSD224L by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.75

Screw

Sold individually.

$2.71

Screw

This screw is sold individually.

$2.71

SCREW

Sold individually.

$2.71

Screw

This is screw is sold individually.

$4.73

Compression Nut

This compression nut is used with the plastic water line of the icemaker assembly.

$18.30

Ice Bin Drive Ring

This part connects the ice auger to the motor through the bin.

$4.80

Plastic Tubing

1/4" Plastic tubing, 8 1/2 feet long.

$4.11

Inlet Hose Gasket

This high pressure inlet hose washer is black. It is an inch in diameter, made of rubber, and used with many washing machines, refrigerators, and dishwashers.

$106.20

Ice Bucket Auger Drive Motor Kit

This motor kit comes with a thermally protected motor, a washer and a mounting bracket. The motor performs eighteen revolutions per minute, carries 115 volts, and drives the auger ...

$10.48

TRAY

This tray is a replacement part for flex tray ice makers.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

the ice/water actuator switch burnt out and was stuck on.

  • Customer: Jon from Nampa, ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 10 of 11 people found this instruction helpful
Removed the rubber cover over the actuator switch. Used a screwdriver to remove the switch, disconnected the wires. I then removed the switch from the mounting bracket using a small philips head screw driver. Installed the new switch on the mounting bracket then installed the switch onto the freezer door. The only difficult part was installing the rubbe... read more

Ice bucket auger yoke was stripped out and turned freely

  • Customer: James from Pineville, LA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 7 people found this instruction helpful
Removed the ice bucket from the freezer. Removed the single screw on the left side with a nut driver, then lift and pull the tray toward you...there is a wiring harness in back of the tray that I had to unplug...easy, pinch the sides of the plastic connector and it disconnects..and the tray came out of the refrigerator...and the cussing started. Since the th... read more

The plastic ring that is the connection between the drive motor at the back of the freezer compartment to the auger in the ice bin shattered when my wife was dispensing crushed ice.

  • Customer: Larry from Anchorage, AK
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
Part selects cataglog for parts selection was very easy to use and the online service and delivery was great.
When I got the part, it was not apparent on how to remove the auger so that I could insert the new connector. There were about about 8 visible screws, with star drive heads that I fortunately had a screwdriver that fit, and I could not tell if ... read more