Models > JMV8208ACB > Instructions

JMV8208ACB Jenn-Air Microwave - Instructions

All installation instructions for JMV8208ACB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JMV8208ACB
1-15 of 27
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Sparks and loud hum from oven

  • Customer: Guy from Bellingham MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 50 of 79 people found this instruction helpful
1. I went to the internet to find the service manual for the Maytag microwave.
2. I opened up the oven and started measuring the resistance of the diode, capacitor, transformer, and magnetron between terminals and then to ground. The transformer and magnetron were well within the resistance limits. The diode was shorted in both directions(+-). The capacitor was fully open in both directions -- high resistance.
3. I ordered the 2 parts, installed them, and ran the oven. Worked perfect first time.
4. Reinstalled oven and worked ever since (1 week so far).
5. The secret was that the transformer had a load hum. I figured the transformer was OK. The magnetron had no short between filaments and ground to filaments. The only two left were the diode and capacitor. The first two are about $200 -- almost the value of a new microwave. The $70 repair was well worth it. If the first two were still bad, then tempted to buy a new oven.

Microwave worked intermittently depending on how door was closed

  • Customer: Robert from Bainbridge Island WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 29 of 35 people found this instruction helpful
Remove top grille (2 screws), undo control panel (1 screw). Tilt down control panel, switches are on the left. There are actually three switches that are involved with the door, two horizontally mounted, one vertically mounted. This would be an EASY REPAIR, but it took me a while to figure out which of the three switches was bad, and also took a while to figure out that there is a plastic rod that inserts through the hole in the switch body. Once i figured this out went like a breeze. Lower horizontal switch was the bad one, but since the kit came with two switches i went ahead and replaced the upper horizontal one as well. IT appears that the horizontal switches are probably more likely to fail than the vertical switch based on the position of the switch and force angles. Works great now!

loud buzzing noise

  • Customer: Sandra from coto de caza CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 30 of 55 people found this instruction helpful
The repair went well...I am so glad that I read this info before buying a new microwave....it saved me lots of money. I did have a repair man come and look at it and he told me to buy a new one but it cost alot of money when it wasn't necessary. I did the repair and I was very proud of myself.
Three men watched a woman fix this and it was no problem...they were impressed also....

No Power to Microwave

  • Customer: John from Palos Hills IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 18 of 37 people found this instruction helpful
After determined the problem on one of the websites...I received the part I needed... removed the control panel and installed the new main fuse In about 15 mins!

The lamp burns out occasionally

  • Customer: Gertrude from Milford DE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 11 of 18 people found this instruction helpful
Once I got the replacement bulb, the repair was
easy. I needed to unscrew one side of the lamp assembly and pop the new bul in.

My problem was getting the right light. The local hardware store didn't carry quite the right halogen lamp and the one I bought burned out the wires that hold the light. THis was a costly repair --- about $100. So I was delighted when Part Select had the lamp I needed. They were prompt in sending it out and I was very satisfied.

Close the door on the microwave, punch in the # nothing happened

  • Customer: Robert S. from Stafford TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 14 people found this instruction helpful
I removed the unit from the wall. Took the cover off. Set the unit on its side. It revealed the working parts. Removed the old micro switches. Put in the new oness. Presto, it worked. Very easy for me.
The parts was delivered almost before my notice they were shipped.

Our maytag microwaive sounded like a thrashing machine when running!

  • Customer: William from East Wenatchee WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 14 people found this instruction helpful
Over a period of a year or so, our over the stove microwaive oven started sounding like a thrashing machine every time we turned it on and got progressivly worse. The repair service wanted nearly half the cost of the appliance to just come out to take a look. I removed the oven from the wall cabinet, removed the cover and discovered that the cooling fan blade had come loose from the motor shaft and was hitting the casing. I ordered the fan motor assembly from you folks, replaced the faulty fan, and the problem was resolved at about one half of the cost of a service call.

replace filter

  • Customer: Donald from Houma LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 14 people found this instruction helpful
removed the cover with a phillips screwdriver and replaced filter

Broken cooking tray

  • Customer: Kimberly A from Howell NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 15 people found this instruction helpful
Just put the new one in and we were good to go!

Fan motor and magnetron did not come on, but every thing else did.

  • Customer: Dale from Chester CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
Problem would come and go. Found service schematic inside unit. Perform all the suggested tests. One possible solution was the primary interlock switch shown on the schematic and a check found the switch stuck. It would free up some times but would stick again in the open position. Ordered switch which was a simple plug in unit.

Needed to push door up to run appliance.

  • Customer: J Patrick from Baltimore MD
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 16 people found this instruction helpful
1. Removed cabinet screws (10-15?). 2. Removed cabinet. 3. Removed top interlock switch which actually was not defective. The press clip connection appeared as if it had been arcing for quite some time and the corrosion created resistance sufficient to prevent the current from getting through the switch. 4. Replaced switch anyway but broke plastic retaining clip despite every effort not to do so. Reset broken clip with super glue. 5. Reassembled cabinet and appliance is in good working condition.

Fan come loose on motor shaft

  • Customer: MARK from BISMARCK ND
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
Repair was very simple, removed microwave from wall and removed top cover and found fan loose on shaft. Removed fan and motor, new motor and fan slotted, good upgrade. Installed new motor and fan and top cover on, installed back on wall plate, tried and wife said it sounds like a new one.

Halogen Lamp Replacement

  • Customer: Giovanni from Mount Prospect IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 9 people found this instruction helpful
Super Easy. I was able to find the part on your website.
The whole process was excellent.

bulb burnt out

  • Customer: Denny from St Louis MO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 9 people found this instruction helpful
Unscrewing the old one out, putting the new one in.

Microwave would not cook

  • Customer: Scott from Mickleton NJ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
All the electrics worked on Amana microwave EXCEPT for the cooking function. Inspected the control board and found the upper switch on the door interlock was burnt. Installed new switch in minutes and everything now works fine. Unfortunately, had to purchase expensive two switch "kit" although only one switch was kaput. PartsSelect mailing was SUPER fast. Thanks for looking, Scott
All Instructions for the JMV8208ACB
1-15 of 27