JMV8196AAW - Instructions

well I unplugged the microwave one day prior to working on it. shock precaution smart way to do this job. very easy pullout the screws behind the unit pull off the outer casing. minor screws inside the unit you have to remove a couple things out of the way. unplug the magnetron and remove first gives you more room to work on the side panel to replace the micro switches. I only replaced one the bottom micro switch. only one bad, but since I was in there I clean the bulb and changed the magnetron any ways. I read other reviews and made my choice to do so. it works perfectly now. Thanks PartSelect for having parts.

Lifted out old support put new one in. Fixed in less than 30 sec.

We needed a phillips head screw driver to remove the single screw holding the light bulb cover in place.
Removing the old bulbs was a little work, because they had come loose from the sockets. We unplugged the microwave, so we could grip the sockets with a tool. I think my husband used a needle nose plier for this.
The new bulbs screwed in easily, and then we refastened the light bulb cover with the phillips head screw driver.

Unplug the microwave. Remove the Philips head and safety Torx head screws along the bottom of the sides and rear of the microwave which hold the black cover on. Lift the cover up at the rear and slide it backwards to disengage the tabs on the front top. Remove the cover. Discharge the capacitor by shorting the terminals to each other and then ground. Do this with a well insulated object and be aware there may be a pop when you do this. Keep hands, etc. on the insulated part of the object (screwdriver handle, etc). There's a lot of stored energy in that capacitor. I'd advise first checking the diode to make sure its not bad. Replace it if it is. The Magnatron is held in with a couple of screws on the top and sides. Unplug the connector and remove the screws. Remove the Magnatron. Installation is the reverse of removal.

Microwave vented up toward the ceiling discoloring it. I positioned the charcoal filter over the vent holding it in place with scotch tape. It keeps the ceiling clean and dose not affect air flow from the exhaust vent. I change the filter every year.

Turn off power supply at breaker . Replace old bulb with new bulb .

I thought that if I went one more time to visit my son, and the microwave tray was still gone (due to their having broken it), I would just order the part MYSELF!! So, that is what I had to do. They have been without this for at least 3-4 months........ Well, it was sitting at my door in less than 48 hours after I ordered it! Easy, easy, easy..........thank you!

removed old covers which were cracked and dirty.
the repair part looked exactly like the original but did not fit correctly. i had to do some changing of the size to make it fit. it does not clip in place as it should but we are living with it as it does cover the light bulb. the grease filter is perfect

screwed in new bulb

Replaced the broken piece with the one purchased at Partselect.com. I was concerned that the part would not be correct since all we did was enter the model number of the microwave. PartSelect.com was really easy to use and sent the correct part. Thanks so much for making this process easy.

Spouse just screwed in the new bulb and reinstalled the light cover plate with the two screws. Took under a minute. Works great.

Husband replaced the bulb

After checking all three switches for continuity I determined that the plastic door lever had warped or gone out of wack. After shutting off power at the breaker box I removed the door, the inside trim piece around the inside of the glass. Removed the black two prong door lever, reattached the new door lever and then reinstalled the trim piece and all screws. Works fine now. Easy fix just make sure your switches are all ok then replace the door lever.

Replaced entire door latch assembly with the three micro switches. Easier to replace entire latch assembly as individual switches do not remove easily from latch assembly. Had trouble removing front panel assembly. Parts ordered solved this problem.

Unplugged the microwave. I opened the door. I used a butter knife to pop the bezel off the inside of the door. I pushed the locker up and to the left and used the butter knife to pry it loose. Disconnected the locker from the spring, and reversed for the installation.