Models > JMC9158BAB > Instructions

JMC9158BAB Jenn-Air Microwave - Instructions

All installation instructions for JMC9158BAB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JMC9158BAB
1-7 of 7
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

microwave oven blew fuse

  • Customer: tad from tamarack MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 16 of 22 people found this instruction helpful
First I removed upper front grill by removing two Philips head screws on top and pulling off. This exposed the Philips head screw which holds control panel in place. After removing screw I pushed up on panel and it came off to expose fuse. With needle nose pliers I removed old fuse and again with pliers held new fuse in position. With the help of a bladed screwdriver, I pushed new fuse into holder, then replaced panel, screw and grill. This took less than 15 minutes even as one of the wires on control panel pulled out of connection and took some time to locate where to reconnect, otherwise was an easy fix
.

microve stopped working

  • Customer: Denice from Montgomery AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 8 of 14 people found this instruction helpful
Jenn-Air Microwave would not turn on. Clock worked , light worked, timer worked and would count down .I changed' Part #0813140 Switch, Micr} cost $8.99 plus shippingNow it works Thank You for good advise

Died while heating lasagna

  • Customer: connie from madison NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 11 people found this instruction helpful
Removed 4 small star head screws from back of microwave, lifted body off, removed blown fuse and replaced with new one (found where cord enters). This model is stainless inside and out and I like it a lot. It is also sold by Daewoo and a few other manufacturers.

Rotate motor for Micrwave turntable failed

  • Customer: Charles from Lake Havasu City AZ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Turn off power to microwave (kitchen circuit breaker) Remove 3 sheet metal screws bottom front, disconnect electrical connections to motor and lights, remove defective motor(1 screw), replace with new unit, replace screw, re-attach bottom (3) screws, test. Replacement motor cost via this supplier was 1/3 of what local appliance repair store would have charged.

no power to unit after replacing fuse

  • Customer: JOE from CENTERREACH NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
went to you tube and found a segment compatible to my issue.called the web site and ordered the thermostat fuse and ceramic fuse in case i had the wrong one purchased at the locale H/Depot. The only issue was I did not know that there was 2 different thermo fuses,,one controls fan and the other a basic one. luckily the fan wasn't the one that was blown.The woman i spoke to was very helpful and my order was AT MY HOUSE in less then 24 hours.

Power cuts in and out; runs for a few secs then powers off

  • Customer: Vinh from Houston TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Disconnected power and removed Microwave housing cover, observed burned end plastic connector of wire connecting to the thermostat (or thermal overload sensor); slightly wiggle one of the 2 wires to the thermostat would cause microwave power to cut out (when plugged in power). When powered on, I would try to run it but power cuts out after just a few seconds. Removed the 2 wires from the old thermostat, removed the 2 screws that fasten down the thermostat, replaced with new thermostat and reapplied the 2 screws; cut off burned part of wire and resolder to new wire connector; reconnect both wires to new thermostat and reinstall MW housing cover. MW works good as new again. Thank you PartSelect!

microwave would not heat.

  • Customer: outstanding from Galena MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
hardest part was taking the microwave down off of the wall to gain access to the diode. Thought if was the transformer but ended up being just a blown diode. remove and replace and bench test. that part took 15 minutes . moral of the story don't boil water under the side of the microwave that holds the electric components.
All Instructions for the JMC9158BAB
1-7 of 7