Models > JMC5200BAW > Instructions

JMC5200BAW Jenn-Air Microwave - Instructions

All installation instructions for JMC5200BAW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JMC5200BAW
1-7 of 7
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

microwave oven blew fuse

  • Customer: tad from tamarack MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 15 of 21 people found this instruction helpful
First I removed upper front grill by removing two Philips head screws on top and pulling off. This exposed the Philips head screw which holds control panel in place. After removing screw I pushed up on panel and it came off to expose fuse. With needle nose pliers I removed old fuse and again with pliers held new fuse in position. With the help of a bladed screwdriver, I pushed new fuse into holder, then replaced panel, screw and grill. This took less than 15 minutes even as one of the wires on control panel pulled out of connection and took some time to locate where to reconnect, otherwise was an easy fix
.

microve stopped working

  • Customer: Denice from Montgomery AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 8 of 14 people found this instruction helpful
Jenn-Air Microwave would not turn on. Clock worked , light worked, timer worked and would count down .I changed' Part #0813140 Switch, Micr} cost $8.99 plus shippingNow it works Thank You for good advise

Died while heating lasagna

  • Customer: connie from madison NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 11 people found this instruction helpful
Removed 4 small star head screws from back of microwave, lifted body off, removed blown fuse and replaced with new one (found where cord enters). This model is stainless inside and out and I like it a lot. It is also sold by Daewoo and a few other manufacturers.

TURNTABLE QUIT

  • Customer: RICHARD from OKLAHOMA CITY OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
SNIPPED FOUR CORNERS OFF INSPECTION PANEL,REMOVED ONE PHILLIPS SCREW AND TWO ELECT. CONNECTIONS. REVERSE PROCESS.

Blown heater element

  • Customer: Dr. John from San Antonio TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Replaced with new microwave. Acquired the same model so it would fit in the space and be covered by the frame border. Screwed base and vent protector in place , slid it all into the space and screwed on the frame. Had plugged it in for testing . Turned it on and am using it today....bought a 4yr extension warranty. Hope I don,t have to repair or replace again...Originally, I had needed a roller guide for under the spinning plate. Did replace it but a few days later the whole microwave stopped because of the heater element.

Bulb out

  • Customer: Clifton C from Kingsland TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Pretty easy tear down and assembly once I removed it from cabinet (built in micro)

Power cuts in and out; runs for a few secs then powers off

  • Customer: Vinh from Houston TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Disconnected power and removed Microwave housing cover, observed burned end plastic connector of wire connecting to the thermostat (or thermal overload sensor); slightly wiggle one of the 2 wires to the thermostat would cause microwave power to cut out (when plugged in power). When powered on, I would try to run it but power cuts out after just a few seconds. Removed the 2 wires from the old thermostat, removed the 2 screws that fasten down the thermostat, replaced with new thermostat and reapplied the 2 screws; cut off burned part of wire and resolder to new wire connector; reconnect both wires to new thermostat and reinstall MW housing cover. MW works good as new again. Thank you PartSelect!
All Instructions for the JMC5200BAW
1-7 of 7