Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JKP90WM1WW

JKP90WM1WW General Electric Microwave Oven Combo - Overview

Get Parts and Repair Help for JKP90WM1WW

If you know the microwave oven combo repair part you need, you can browse the list of all parts on the JKP90WM1WW, or you can search by name or part description. You can also find your part by where it is located on the JKP90WM1WW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your microwave oven combo. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$7.63

Line Fuse

This ceramic microwave fuse is just over an inch in length. It is white in the center, and metal on both ends. This is a 20-amp fuse, and is used to power your microwave. If the to...

$10.48

Temperature Sensor

The temperature sensor, also known as the oven temperature sensor assembly is usually found in the back of the oven. The function of the oven temperature sensor assembly is to measure the temperature inside your oven while it is on and send the temperature back up to the electronic control, which adjusts as necessary. If your oven is having difficulty achieving warmer temperatures and/or keeping warmer temperatures up, you may want to test your temperature sensor. Before you make this repair remember to unplug your range from the power source, and turn off the gas shut off valve.

$21.50

Secondary Door Switch

The secondary door switch is a simple on/off mechanism that stops the microwave from operating when the door is open. The switch monitors the door latch position, and communicates ...

$19.73

Monitor Door Switch

Unplug your microwave before attempting this repair. You will need to remove the grill, which is held into place by two screws at the top of the grill (open your microwave door before doing this). Remove the grill. Remove the screw on the left holding the control panel in place. Loosen the screw behind the panel. You should now be able to lift the panel up and pull forward to detach. You will find the door switch by removing the screws to detach the switch assembly. Press on the release tab to remove the middle switch. Disconnect the wire connector to release the old switch.

$33.44

Turntable Roller Guide

This roller is located underneath the glass turntable. With the help of the motor, this roller helps to rotate the glass tray. This part takes the place of the coupling.

$36.28

Diode

This part allows power to go one way only.

$13.58

Halogen Light Bulb - 50W

This light bulb is used in the interior oven.

$2.06

Screw

This screw is sold individually.

$3.29

Screw

Sold Individually.

$3.52

Screw

Sold Individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Microwave completely stopped working

  • Customer: Kim from Cliffside Park, NJ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 732 of 959 people found this instruction helpful
Turned out the issue was easily solved by replacing a single, inexpensive fuse.

First off, UNPLUG THE MICROWAVE.

The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the microwave and remove an... read more

light worked, timer and control pad worked, but no turntable, no heat, no noises of any sort, just didn't start up

  • Customer: Marla from Arlington, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 224 of 256 people found this instruction helpful
Noted on partselect.com that someone else with this problem, found it to be secondary door switch. There are three door switches in this model, but online info noted that one of the three might feel "soft" (in my case, one switch clicked in a rather "jiggly" way, the other two were strong decisive clicks.) To access the door switches on this model was the ... read more

Oven would go in to a F2 Error

  • Customer: Peter from stamford, CT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 76 of 100 people found this instruction helpful
Removed six 1/4" hex nuts on rear of oven. Then through front/inside removed a single 1/4" hex nut to actually remove sensor. Unplug sensor connector, remove. Reversed steps, push oven back in place and plugged in. Tested oven function. read more