Models
>
JKP36005
JKP36005 General Electric Range - Overview
Sections of the JKP36005
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Bake Element - 240V
PartSelect #: PS249424
Manufacturer #: WB44X200
This is a 240 volt bake element for your oven or range. The kit comes with two installation screws and the element. The element functions by supplying heat from the bottom of the oven to bake or cook ...
$45.72
In Stock
Broil Element
PartSelect #: PS249411
Manufacturer #: WB44X173
The broil element is located at the top of the oven and gives off heat in order to bake evenly. If you notice that the element is not heating up or is not cooking evenly it could be because it is brok...
$31.03
In Stock
Oven Door Gasket
PartSelect #: PS242058
Manufacturer #: WB2X3138
This door gasket or seal is used in ranges and ovens. The rubber gasket creates a protective seal between the oven door and the opening of the oven. The function of this seal is to trap heat and preve...
$183.95
In Stock
Oven Door Inner Glass Window Assembly
PartSelect #: PS251937
Manufacturer #: WB56K19
No Longer Available
Self Cleaning Dual Range Thermostat
PartSelect #: PS236059
Manufacturer #: WB21X5320
You won't find an "off" position on this dual range thermostat because the "off" function of this thermostat is controlled by the selector switch. This thermostat operates on a range of 150 degrees to...
No Longer Available
Questions And Answers for JKP36005
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the JKP36005
[Viewing 7 of 7]Little to no heat when baking
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Little to no heat when broiling
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replacment of the bake unit
The hardest part was removing the old nuthead screws off the old bake burner. Once those were off installing the new bake element was simple. One screw in each wire terminal, two hex head screws to hold the unit in place. Works like a charm!
Parts Used:
-
Beth from Matthews, NC
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Socket set
610 of 624 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven lower burner burned out
Very easy, remove two screws, pull burner unit out slightly, then remove the two screws attaching the wires, one to each side, remove old unit and replace with new unit and replace screws.
Works fine perfect replacement.
Works fine perfect replacement.
Parts Used:
-
james from franklin, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
507 of 590 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bake element was on its last legs, starting to crack but still functional.
Removed the racks, unscrewed the back plate which holds the element, unscrewed the leads from the element, removed the old part.
Reversed the process to install the new element.
Turned the oven on for a few minutes to burn any contaminates off the new element, replaced the racks.
And that was it; quite ea ... Read more sy.
Reversed the process to install the new element.
Turned the oven on for a few minutes to burn any contaminates off the new element, replaced the racks.
And that was it; quite ea ... Read more sy.
Read less
Parts Used:
-
Lawrence from San Jose, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
223 of 373 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!