Models > JJW9630AAB > Instructions

JJW9630AAB Jenn-Air Oven - Instructions

All installation instructions for JJW9630AAB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JJW9630AAB
46-60 of 157
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven door locked and was flashing code F4

  • Customer: Mary L. from Trinity TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
First, thanks to PartsSelect for getting the part to me so quickly. I went to the "Instant Repairman" , checked all that applied to my problem. The answer was the sensor, 99% of the time.I used a coat hanger to pull the latch back and open the door. I watched the video and followed the instructions to remove the old sensor. The wires were melted but the plug was still good. I used one of the adapters to install the new sensor, then replaced the two screws inside the oven. I pulled the stove out because I had read in the reviews that you needed to get the plug behind the insulation away from the oven wall. I was lucky ,there was a small hole in the back ,right behind the sensor.I gently pulled the wire and plug to the back ,well away from the oven wall. Put the stove back in place ,threw the breaker and was back cooking again!! My stove has a downdraft vent, took me longer to hook the vent back up than to install the sensor..Oh yes, did I say,I am a75 year old female and I did it all myself..

ovens wouldn't maintain temperature after preheat cycle

  • Customer: sherri from elk horn IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
unplugged oven. removed 2 screws that hold the sensor in place, then removed the dozen or so screws that hold on the rear panel, unplugged sensor and fed wire through insulation. identified and installed correct harness adapter then fed new wire and connecter through insulation and connected to adapter. installed sensor retaining screws.plugged oven back in and tested function.no dice. unplugged oven once again. removed oven control panel and upon inspection of printed circuit board discovered 3 solder joints had failed. dang. resoldered failed joints and also sweetened up a few others that looked suspect. reinstalled controller, replaced all retaining hardware, and plugged in the oven. tah-dah!! works like a charm now. moral of the story is check the pc board first and save $50 for unneeded pats!!! or buy the controller from parts direct for $260ish. btw a roll of solder and soldering iron from an auto parts store cost around $10, learned to solder on you-tube $0. amazing all the home appliances yo can fix if you're not afraid to take a few screws out and poke around a bit. CHEERS!

The Old Hinges broke off and the door would not stay closed

  • Customer: Bruno from Scottsdale AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
I removed the single screw on each side of the oven by the hinge to remove the hinge cover plate and expose the hinge opening. I lifted off the glass oven door up and out and set it on my work bench. The door is heavy because its glass so make sure the doors on the way to the garage are open to your work bench area. I installed the cover plates back on so i would not loose the little covers and screws. I removed the screws all around the door and set them in a cup and lifted up the inner part of the door and the hinges are exposed. After removing the screws that hold on the hinges it lifted right out. I cleaned all the glass and set the new hinges in and locked them down with the screws and installed back the inner part of the door to the outer part and returned all the screws back. I then removed they screws on the hinge covers. I did not loose them with 4 kids running around and lifted the door back into the hinge openings and pushed down and it locked in. I then put a little pressure down on the door and removed the little locking pins. I pushed the door all the down and installed the hinge covers back on and it works beautiful. I think the new hinges are better than the set that came with the Jenn-Air wall oven. Thanks Parts Select. Also the new hinges came in 3 days as promised.

replace door hinge

  • Customer: Larry from Oak Grove MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
The repair was very easy to perform, but the springs in the new hinge were not as strong as the old one. The door would not close all the way unless you held it closed. The hinge looked identical but spring had less tension.

No temperature control

  • Customer: Max from Houston TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.

the hinge sring broke on one side of the oven door

  • Customer: stephen from canton MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
Remove the screws from bottom of door to gain access to the hinge screws. Remove the bottom hinge screws and then open the door to gain access to the top hinge screws. CAUTION after removing the top screws close the door as far as possible while still griping the sides of the door. Pull up on the sides to remove the door from the stove. The springs are fully loaded if you have the door open all the way and try to lift up (like I did) the hinge will spring back and get your finger. Install the new hinge, put the door back into the oven, install all the screws and then remove the temporary rivet that comes installed in the new hinge.

lower oven wouldn't operate

  • Customer: t from mt. juliet TN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 9 people found this instruction helpful
replaced the relay board after trying to understand the instructions. they were vague regarding when or if a jumper wire was required.

have had to work on this oven several times.touchpad, "clock, elements

Oven was not correctly heating to set temperature

  • Customer: Trace from Ofallon MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 2 of 3 people found this instruction helpful
Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces of sheet metal back on and plugged in the oven.

oven not heating to set temp. 100 degrees too cold

  • Customer: Robert from Funston GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.

Display was not readable anymore - numbers faded away

  • Customer: Bernd from Westford MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
Switched off power !
Removed the control panel by removing four philips screws under the panel. marked all the connectors with a permanent markers (socket & cable) to be able to identify the right direction. Removed the old clock assembly by removing 4 hex screws.
Then assembled new unit and reversed steps...
Clock and oven temperature is again readable and very bright!
initially I got a replacement part that showed the same error as the original part, but this unit was replaced within one (!) day under the Partselect warranty plan. Good job!

Digital display was almost unreadable

  • Customer: STEVE from ORANGEVALE CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Removed 4 screws that held upper panel.
Removed 4 screws that held clock assy.
Piece of cake!

I put a new digital clock in my oven.

  • Customer: Kenneth from spring TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
The total repair time was less than 5 minutes. I turned off the circut breaker to my oven. Directions were very easy, remove 4 screws, take plugs off old unit, place them on new unit, remove 4 screws with nut driver, place new clock in place and put the screws back in. Go out and turn on power to oven. Set the clock.

couln't read clock or temp but oven worked

  • Customer: ricky from lookout mountain TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 1 of 1 people found this instruction helpful
Soooooooo easy- I am a house wife and did it- turned off power and unscrewed 4 screws and then a couple more and unplugged wires then replugged to new piece/part then screwed all screwss back in- EASY- woulda cost 400 for parts and labor

Display too dim to read

  • Customer: Kevin from San Antonio TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Opened breaker feeding power to oven

Removed 4 screws on underside of front panel; display module is attached to back side of panel.

Unplugged wiring harness from panel circuit boards and display module. Set panel face down on towel to keep from scratching it.

Removed 2 screws holding display to panel

Replace module and re-attached to panel

Plugged harnesses back in

Re-attached panel

Turn on breaker. Done.

the digital lights in the clock went out

  • Customer: NEVIN from TROY OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 1 people found this instruction helpful
First I removed four screws from the bottom of the control panel and removed the control panel to expose the clock assembly. Then removed three connectors from the clock,removed two screws from the clock and removed the defective clock assembly. By reversing the procedure I installed the new assembly and was finished in about 15 minutes.
All Instructions for the JJW9630AAB
46-60 of 157