Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JJW9530CAW

JJW9530CAW Jenn-Air Wall Oven - Overview

Get Parts and Repair Help for JJW9530CAW

If you know the wall oven repair part you need, you can browse the list of all parts on the JJW9530CAW, or you can search by name or part description. You can also find your part by where it is located on the JJW9530CAW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your wall oven. We’ve also included any installation videos we have for JJW9530CAW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.88

Light Bulb - 40W

This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these repla...

$29.74

Long Oven Sensor

This long oven sensor is also commonly known as a temperature sensor. It is designed for use with ovens and ranges. It is similar to a thermostat; it measures and regulates the internal temperature of your oven cavity. There is an adapter at one end, a probe at the other, and they are connected by an insulated wire. The probe is approximately 7 inches long. You can test the sensor with a multi-meter for functionality. You need to check the model-specific manual to determine what the proper resistance is for your specific appliance. This oven sensor comes with two wire harness adapters and a set of instructions.

$3.02

Screw

This screw is sold individually.

$5.52

Screw

Sold individually.

$42.95

Door Hinge

The hinges control the rate that the oven door opens and closes, and allows the door to stay open at an angle. This hinge can be used on either the left or right hand side of your ...

$57.33

Bake Element

This bake element for your oven, range, or stove provides heat from the bottom of the appliance to cook or bake your food items. You may need to replace this part if your oven is not heating properly. This bake element is approximately 22 inches wide. Disconnect power to your appliance before completing the repair because you will be working near electrical wiring harnesses. The wiring harnesses feature slip-on terminals for easy installation. Be sure to hold the wiring harness forward so they do not fall behind the panel, as they are difficult to retrieve. This is an authentic OEM bake element.

$48.18

SEAL- DOOR

This oven door gasket prevents heat from escaping the oven cavity when in use. This is a very easy repair that should only take a few minutes. The door gasket may damage or rip ove...

$3.19

Screw (4)

Sold Individually.

$63.26

Broil Element

This broil element is found on the roof of the oven.

$47.45

Oven Rack

Sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven not holding 350 F, when cooling the coils did not reheat

  • Customer: David from Westford, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 118 of 137 people found this instruction helpful
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. ... read more

No clock display

  • Customer: Cheryl from Mesa, AZ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 52 of 53 people found this instruction helpful
1. Turned off the circuit breaker for the oven.
2. Opened oven door used a phillips screwdriver to remove four black screws from under the top panel.
3. Lifted panel slightly & removed from oven.
Removed four screws using 1/4" nut driver to remove old display unit. Disconnected three wire harnesses.
4. Connected three wire harnesses to n... read more

F1-1 code

  • Customer: charles from marstons mills, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 52 of 67 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Failure to do so will ... read more