Models > JJW9530ACW

JJW9530ACW Jenn-Air Oven - Overview

Get Parts and Repair Help for JJW9530ACW

If you know the oven repair part you need, you can browse the list of all parts on the JJW9530ACW, or you can search by name or part description. You can also find your part by where it is located on the JJW9530ACW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your oven. We’ve also included any installation videos we have for JJW9530ACW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.58

Light Bulb - 40W

Sold individually.

Order within the next 12 hrs and your part ships today!
$28.12

Long Oven Sensor

This oven sensor kit comes with two harness adapters. This sensor detects the temperature within the oven cavity.

Order within the next 12 hrs and your part ships today!
$36.91

Door Hinge

This hinge is located on each side of the oven door.

Order within the next 12 hrs and your part ships today!
$2.70

Screw

This screw is sold individually.

Order within the next 12 hrs and your part ships today!
$18.07

2 Piece Broiler Pan

The top of this part is now black.

Order within the next 12 hrs and your part ships today!
$50.61

Bake Element

Order within the next 12 hrs and your part ships today!
$28.99

Light Lens

Order within the next 12 hrs and your part ships today!
$53.52

Temperature Probe

This temperature probe consists of two ends joined together by an insulated wire. The small end, the jack, plugs into the range, while the longer end, the probe, is inserted into the meat.

Order within the next 12 hrs and your part ships today!
$45.20

Oven Rack

Order within the next 12 hrs and your part ships today!
$39.75

Door Seal

This oven door gasket prevents heat from escaping the oven cavity when in use.

Order within the next 12 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven not holding 350 F, when cooling the coils did not reheat

  • Customer: David from Westford MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 81 of 93 people found this instruction helpful
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. ... read more

No clock display

  • Customer: Cheryl from Mesa AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 45 of 46 people found this instruction helpful
1. Turned off the circuit breaker for the oven.
2. Opened oven door used a phillips screwdriver to remove four black screws from under the top panel.
3. Lifted panel slightly & removed from oven.
Removed four screws using 1/4" nut driver to remove old display unit. Disconnected three wire harnesses.
4. Connected three wire harnesses to n... read more

F1-1 code

  • Customer: charles from marstons mills MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 33 of 39 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Failure to do so will ... read more