JJW8630DDQ Wall Oven - Instructions

This is fairly easy for anyone to do. First I opened up the front (silver part) of the oven door by removing the screws at the top and the bottom. Then I kept on removing the various layers of glass... the 2 outside ones are removed by removing their respective screws and then you get to the inner-most. These 2 inner ones are in a frame that holds them together. I removed the large silver frame that holds the insulation and the 2-glass-frame in it. Just remove the screws and then tilt the insulation frame out a bit to remove the glass frame. You can tilt the entire insulation holder out but the insulation is soft and it starts to fall off. Just tilting it enough worked for me. Then I opened up the glass frame from one end, removed the left-over broken piece of the old glass pane and installed the new one in. Then reassemble. The entire process is very easy - but you will need another person for a few minutes when you remove /reinstall the glass frame inside the insulation holder. You would just need a little help holding everything... nothing technical. I would rate the repair technicality at 4 or 5/10. It could even be a 3 if there were less steps involved. Good luck! By the way, Amana/Maytag wanted $70 or so for the glass and then the repair fee. I got the part here for about $50.

Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.

First I opened the door to the oven. Then I opened the box that the part came in. (knife) I then slid the oven rack out of the box and unwrapped the plastic, being careful not to bend or scratch the new rack. Now, this is the tricky part... I had to move the existing rack down one space to make room for the new one. Then carefully slid the new rack in, tipping it slightly and sliding it in. LOL

removed oven door, removed screws from bottom and sided, door is in layers, removed door layers like taking apart a sanwhich layer by layer, once i got to the inner layer i just had to bend out the little tab on the frame,remove the broken pane and place in the new one, bend the tab back and then put the door back together layer by layer, it was very easy and saved me money, and frustration in dealing with a repair man from a well known company who tried to tell me I needed to replace the whole door as the glass was factory sealed in the door, WELL! this girl's hair may be blonde but not that blonde, I received the glass the very next day, and it took me 40 minutes tops to replace the glass, EASY! KC

Remove the oven door. Remove 3 self tappers on rear wall of oven to take off a round access panel. Pull out a pre-cut rectangle of insulation. Next I removed the 2 screws holding the sensor in place. Pulling the sensor out a bit told me I was "touching" the correct wires in the SMALL rectangular opening. The wires are not visable and 2 hands do not fit in this small opening.I looked at the NEW sensor to see the release on the sensor plug. Slip the angled needle nose into the opening and grasp the plug/release side. The plug pulled apart easily. The sensor wire pulls out with a little bit of twisting to fit it out the hole. The new plug pushes in and has to be worked down to where you can reach it. The same angled plier works to re-attach it. It takes longer to read this than to do the job. Best of luck, Al

Replaced the hinges, the appliance never really shut 100% and after several year it got worse. Now it is perfect and we don't have any problem with heat up time of oven, used to take extra long to get to desired temp. Should have sent it back in the beginning.

I removed the door from the oven and set it on towel on the table, and started the repair of the door. I removed the screws one at a time, and one layer at a time. Becareful you need to take the whole door apart, and remember how it goes bact together. In the end it was worth it. The hardest part was getting the right part. I thought I could order the whole door, and found out after several calls they don't sell the whole door. Part Select both times I put in my order had the parts at my door within 2 to 3 days. I also had to return one of the parts and within 2 to 3 days the part was credited to my account

Removed old seal by pulling each little metal prongs out from holes in door frame, then positioned new seal by inserting its prongs into holes in door frame, making sure seal is sitting right in place.

remove oven door from oven,(this is done by pulling down on lock tabs at top of hinge,then with door open about 1/3rd, lift door straight up and out). remove 6 screws from top and bottom of door. remove door handle screws located behind shield. then lift old panel out and replace.

Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answered my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.

Sincerely
Peter from Maryland

This was an easy repair and the parts fit perfectly. I removed the oven door by unlatching it and sliding it off. I then used a screwdriver to take the back cover off, and took the old hinges off with the screwdriver and replaced them with the two new ones that I ordered. I replaced the back of the door panel and put the screws back in and WA LA - just slid the door back on and tightened the latches.

needed to completely dis assemble the oven door to get to the inner pane of glass...took some time...I was able to do it on my own...could possibly go a little quicker with two people for a few of the steps...but possible by one...then reinserted the glass pane...and then need to re assemble the door layer by layer...up and working again...would have cost several hundred dollars if need to call a repair person in...this way was the cost of the piece..less than $70 ... and my time...well worth it....thanks

I took the oven door apart, pulled out the broken fragments of glass and replaced it with the new glass. I should have taken notes as I took the door apart because it was a bit tricky to remember how all the pieces fit back together.

I was very impressed with how quickly the parts were shipped and the quality of the packing materials to protect the glass as it was shipped.

If doing this for the first time, it's harder to replace than described by others.

Start by removing the oven door. Reach in to unscrew the two screws that hold the sensor in place on the back wall of the oven. I was working on the upper oven of a double wall oven and found it more comfortable to sit on a tall bar stool while working. Pull the sensor partially out and you will see the connector wire running through the sensor opening. The sensor connector plug is too deep into the oven to reach with fingers or any tool. Next unscrew the 6" round heat circulator fan just below the sensor on the back wall of the oven. Pull the fan partially out and you will see the plug for the temp sensor directly behind. You may have to push some of the insulation of out of way. Unplug the old sensor and pull it back out directly through the sensor opening. Take the new sensor and thread it in through the opening and plug it in. Reinstall the circulator fan and then screw the new sensor in place. This should complete the temp sensor replacement.

Removed both oven doors to remove from the wall. Pulled the oven out of the wall. Removed all the sheet metal backing on the back of oven top and bottom. Removed the electrical,connections to the fan. Removed attach,net screws and pulled the fan. A bit of a pain had to twist pull and bend the metal bracket. Replacement fan had to be reversed came apart easily and reversed then reassembled. Fit in easily and attached electrical connections. Then reattached all the sheet metal backing bottom then top. Put oven back in wall then secured in place. Re installed the doors and applied power. Oven worked great as soon as we tested it. Great fix, works better than new!