Models > JJW8530CCB > Instructions

JJW8530CCB Jenn-Air Oven - Instructions

All installation instructions for JJW8530CCB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JJW8530CCB
1-15 of 166
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven not holding 350 F, when cooling the coils did not reheat

  • Customer: David from Westford MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 71 of 80 people found this instruction helpful
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.

No clock display

  • Customer: Cheryl from Mesa AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 44 of 45 people found this instruction helpful
1. Turned off the circuit breaker for the oven.
2. Opened oven door used a phillips screwdriver to remove four black screws from under the top panel.
3. Lifted panel slightly & removed from oven.
Removed four screws using 1/4" nut driver to remove old display unit. Disconnected three wire harnesses.
4. Connected three wire harnesses to new display unit & replaced four nut screws.
5. Hang the top panel on the top of oven & replace four screws removed in step 2.
6. Turn on the circuit breaker for the oven.
("Very easy! I'm a 63 yr. old woman!)

F1-1 code

  • Customer: charles from marstons mills MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 27 of 31 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Failure to do so will cause the plastic plug connector to melt from oven heat.

The clock and temperature control became dim and unreadable.

  • Customer: Herb from Seminole FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 18 of 18 people found this instruction helpful
First I turned off the power at the breaker. Then I removed the 4 screws holding the panel in. These screws are located under the panel and accessed when the oven door is opened. The only caution is not to take all the screws out. Just the 4 that hold in the front panel.The panel came off by lifting it and pulling it slightly forward. Then I removed the 3 wiring harnesses. I then used a 1/4 inch socket wrench to remove the (4) screws and replaced the clock unit with the new one. I tightened the 4 screws, re-installed the wiring harnesses and swung the panel back in place . I then locked it in place with the 4 screws on the bottom of the panel. When I turned on the power and my wife saw the lit up clock she was so happy! End of story.

Repeated oven temperature sensor fault codes.

  • Customer: David from Arlington VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 17 of 19 people found this instruction helpful
First I removed the two philips screws inside the oven that hold the element in place. Then I pulled the sensor out and the two insulated wires through the hole to reveal the plastic connector. I unsnapped it from the connector and replaced it with the new element. Then, behind the oven, I removed five or six philips screws on the right side of the large panel so I could pull the wires back through the layer of fiberglass insulation to make sure only the sensor itself would be exposed to the oven's heat. I then secured the back panel again and replaced the two philips screws holding the sensor in place.

Oven door doesn't completely close, light stays on

  • Customer: John from Harvard MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 22 of 36 people found this instruction helpful
I replaced the hinges on the door, it wasn't that hard to do, a couple of minor things I had to overcome. But the new hinges still don't close the door completely. The light still comes on. I don't think the springs in the hinges are strong enough.

I asked for a particular part number in my order, the sales rep, said that wasn't the correct part number, and gave me a different part number. Now I'm not sure if the sales rep gave me the correct part or not.

Either way, I spent money for new hinges, and my own labor, and I still have the same problem.

I've placed calls with Jenn-air, and local technicians, but so far, do not have a solution to my problem. So overall, I'm not very happy.

Anyone got any ideas?

element started sparking and caught on fire

  • Customer: AL from TINLEY PARK IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 15 of 18 people found this instruction helpful
turned off breaker for oven,opened door, removed racks,removed two screws,pulled out the element, dis connected wires,reconnected new element,put back screws,replaced racks,turned breaker on,perfect fit.

Oven door wouldn't close completely

  • Customer: William from Statesville NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 11 of 13 people found this instruction helpful
Parts arrived in three days and it was an easy swap of the hinges but the same problem still existed: the oven door wouldn't close completely, so the oven light stayed on and the convection wouldn't work either unless the door closed all the way. The replacement hinge's springs apparently aren't strong enough to close it and the springs aren't adjustable - which is a design flaw. I did correct the problem though, by using three dollars worth of 1" round magnets, which I placed inside the door: they stay put and are strong enough to pull the door tight.

Oven wouldn't heat the right temperature (you would have to add 100 degrees on to it)

  • Customer: Claudine from Bethlehem PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 10 of 10 people found this instruction helpful
Pulled oven out of the cabinet/wall and pulled sensor out and replaced with new one.

defective oven sensor

  • Customer: sean from easthampton MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 10 of 11 people found this instruction helpful
Checked online to see what F3 readout on stove meant. It meant replace sensor. Ordered part on a Sunday and part delivered Tuesday, Monday being MLK day. Detached bad sensor(2 screws inside oven)had to pull new sensor connector through hole from behind as insulation was too heavy (only removed 4 screws on right rear panel.Clipped wires together and reattached sensor inside oven. A cakewalk.

Clock digital read out dim to non-existant

  • Customer: John from Tempe AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 10 of 11 people found this instruction helpful
This was soooo easy, yes even you Mr. All thumbs, can do it. First it was nice to receive the exact parts I needed from PartsSelect. I needed to take the 4 screws that held the wall oven in place and pull it out about 1". Then, using a battery powered screw driver I removed 4 screws for under the Clocks panel, (you'll need to open the door, can you handle that?). After you've done that simply lift the Glass up and off by grasping the panel and with thumbs on the bottom tilt bottom toward you as you lift up, comes right off. Now disconnect the wire ribbons (4 of them) to seperate the panel from the oven and set the panel down on a towel on the table. Now using a nut driver take out 4 "nuts" and replace the clock card. Be sure to wipe off the INSIDE of the glass panel while you have the card out, and wipe the cards glass so the digital readout will be crystal clear. Re-assemble in the reverse order and you are done. Should take you less then 15 minutes and your wife will think you are a hero! (or you wives can do it and impress the husband!)

Code said we needed a sensor

  • Customer: Janice from Portland OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 11 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires to remove the old sensor. Went on line to find out where to order it from. Ordered it, It was on back order but was only about 1 week to receive. Reversed the procedure. WA LA. It works great.

Lower oven intermittant operation-cleaning

  • Customer: Keith from Canyon Lake CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 10 of 14 people found this instruction helpful
Diagnosis is the important aspect. Ovens have plunger-type switches to tell the "brain" door is closed, both for the light AND to allow initiation of self cleaning. Finally discovered one of those switches was "scratchy" in operation and unreliable in closing the circuit. (Push the plungers in and out several times and observe the light.) If not 100% reliable, replace that switch (cheap and easy with a Phillips screwdriver.) Initial guess was a $major "brain"-electronics problem but it was merely a sticky switch. Strange since the unit is about a year and a half old and rarely used. Found the part easily with PartSelect, and it came via UPS quickly.

oven door gasket was no longer flexible, but stiff

  • Customer: cheryl from dolores CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 11 people found this instruction helpful
pulled out the old door gasket, it had little diamond-shaped clips, pulled out really easily, replaced with the new gasket. All the clips fit into the proper holes, stuffed the new ends where the old ones were. Perfect. less than 10 minutes. Thanks....

Oven door hinges broken

  • Customer: Russ from Jacksboro TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 9 people found this instruction helpful
Removed the door then the end caps and inner panel then the hinge system and replaced with the one piece new set of hinges and back together done in 30 to 45 minutes The new parts were a perfect replacement.
All Instructions for the JJW8530CCB
1-15 of 166