Models > JJW8530CAB > Instructions

JJW8530CAB Jenn-Air Oven - Instructions

All installation instructions for JJW8530CAB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JJW8530CAB
76-90 of 161
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Time light dimmed and then no longer seen

  • Customer: Carol from Kilgore TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 1 of 1 people found this instruction helpful
First I had to remove the cover for the oven because my appliance is an oven/microwave combination. Then I just followed the directions of the people on site and it worked like a charm!!!

Broken oven door hinge

  • Customer: Stephen from Monmouth OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
I watched a You Tube video,removed and dismantled the door, installed the new hinge. I forgot to remove the small pin which is similar to a rivet. When I tried to close the door it bent. Eventually, I remembered the shipping pin and pulled it out with any damage. Believe it or not, I had read about the shipping pin on customer comments on PartsSelect...Good luck, it is relatively easy!

The Old Hinges broke off and the door would not stay closed

  • Customer: Bruno from Scottsdale AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
I removed the single screw on each side of the oven by the hinge to remove the hinge cover plate and expose the hinge opening. I lifted off the glass oven door up and out and set it on my work bench. The door is heavy because its glass so make sure the doors on the way to the garage are open to your work bench area. I installed the cover plates back on so i would not loose the little covers and screws. I removed the screws all around the door and set them in a cup and lifted up the inner part of the door and the hinges are exposed. After removing the screws that hold on the hinges it lifted right out. I cleaned all the glass and set the new hinges in and locked them down with the screws and installed back the inner part of the door to the outer part and returned all the screws back. I then removed they screws on the hinge covers. I did not loose them with 4 kids running around and lifted the door back into the hinge openings and pushed down and it locked in. I then put a little pressure down on the door and removed the little locking pins. I pushed the door all the down and installed the hinge covers back on and it works beautiful. I think the new hinges are better than the set that came with the Jenn-Air wall oven. Thanks Parts Select. Also the new hinges came in 3 days as promised.

bake element weakened in one spot and burned through

  • Customer: Paul from Woodward IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 2 of 5 people found this instruction helpful
I removed two screws holding the element in place. Carefully pulled the element from its mounting throught insulation to expose the two wires connected by electric wire clips. I removed the clips and searched the part online using google. Part Select was provided as the top source. I ordered the part and it was delivered in two days. Taking care to thread the connection through the insulation, I was pleased to have installed it in about 5 minutes. All tools were still out and ready for use. Thank you for your service

Oven Temperature was 50 degrees low

  • Customer: Eugene from Clinton IA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.

F1-1 and F3-1 error code

  • Customer: Barbara from Lakeville MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 5 people found this instruction helpful
Very easy to repair, but you have to be able to pull your stove out. Two screws in the oven and then remove part of back cover of oven and one plug from there. Simple to do, but did not fix our problem. We are waiting repair now from service company as it looks like it needs a control panel. Worth trying yourself to fix the problem. Inexpensive part and easy to install. Also be sure to turn power off your oven to reset the control panel as this may fix the problem - try this first and also after installing new part - like rebooting a computer...

Clock/Oven Display Light went out

  • Customer: Steve from Tracy CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 1 of 2 people found this instruction helpful
First I removed the 4 screws that hold the cover in place. I then removed the 4 screws that held the clock. I pulled the element out about 3 inches and disconnected the 3 wires, swapped the old with the new clock and reinserted the screws.

The great thing though was my order arrived the day after it was ordered. Good going!

Clock and oven display was dim, could not read

  • Customer: William from Escondido CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Remove trim piece from microwave above oven.
Remove 5 screws from inside oven below the display and control module
Lift out module and unplug three wire harnesses
Remove display and PCB from module.
Install in reverse

display very dim but controls still work.

  • Customer: Scott from Jemison AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
the glass front that houses the clock has four screw just above the door. Open the door to access the screws. Once the screws are out,
the glass front can be lifted up off the oven.
Instead of replacing the housing and the circuit board I removed the board from the housing and
and it snaps back into the old housing.

the hinge sring broke on one side of the oven door

  • Customer: stephen from canton MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Remove the screws from bottom of door to gain access to the hinge screws. Remove the bottom hinge screws and then open the door to gain access to the top hinge screws. CAUTION after removing the top screws close the door as far as possible while still griping the sides of the door. Pull up on the sides to remove the door from the stove. The springs are fully loaded if you have the door open all the way and try to lift up (like I did) the hinge will spring back and get your finger. Install the new hinge, put the door back into the oven, install all the screws and then remove the temporary rivet that comes installed in the new hinge.

Electronic panel on oven went blank; oven still worked if you recalled where to press

  • Customer: Jane from Smithfield PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Actually, my brother was visiting and he removed the screws that held the panel in place, pulled it out and disconnected all the wires, noting how things were connected. Each set of wires was fairly idiosyncratic in shape and color, making it pretty obvious how they connected, but one tripped us by having several different ways that seemed to fit. After one negative trial, he found the right way to make it fit. We were amazed at how easy it really was.

Oven would not heat

  • Customer: Ralph from Nicholasville KY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Flipped off breaker and removed oven door and pulled built in stove out so the back panel could be removed. Unplugged the sensor then removed the two screws securing the old sensor inside the oven and installed new sensor. Put stove back together and installed back into counter top, re-installed oven door, flipped on the breaker and oven works like new.

Dried out seal

  • Customer: Clark from Abbeville AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
The repair did not happen as the seal was much larger (fat) than pictured. The one inch graph paper indicated the seal was 1/2 inch wide, which was the exact measurement of existing seal, but when it came it was closer to a full inch wide (fat)? This was my last hope as no one else has the right one either!

Oven control portion of the electronic clock assembly failed (became too dim to read).

  • Customer: Gary D. from Petoskey MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 3 people found this instruction helpful
This is a straight forward part replacement. You will need a phillips screw driver, a hex nut driver, a towel folded lengthwise, and a flash light. A second person's hands are helpful, but not necessary if you have a folded towel ready to use. First, shut off the electricity to the oven at the circuit breaker. Then open the oven door and remove the four phillips head screws under the oven control panel. The panel will then lift up and out easily. Highly recommended: have a second person present to help hold the control panel securely while you remove the three wire cable plugs from the existing electronic clock assembly to avoid scratching the plastic surface of the control panel against the sheet metal brackets that hold it in place. Alternatively, have a folded towel handy so that you may rest the control panel face down on the sheet metal brackets from which it was removed with the folded towel protecting it from being scratched by the metal brackets. Once the wire cable plugs have been removed, the control panel may be moved to a safer location with a soft surface (on a towel or other protective surface) to remove the four hex screws that hold the clock assembly to the control panel. Substitute the new part and replace the hex screws to hold in place. Attach the three wire cables to the new clock assembly, set the control panel back into it's brackets, and replace the four phillips screws to hold it firmly into place. Reset the circuit breaker to the oven. Reset the clock time, which will be 15 to 30 minutes slow (the time you had the power off). Done!

The oven display had stopped working.

  • Customer: Leigh from Lakewood CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 1 people found this instruction helpful
We followed the 63 year old lady's repair directions found on this website and were able to install the new display board in less than 15 minutes. As she said, it was really easy!
All Instructions for the JJW8530CAB
76-90 of 161