JJW8530CAB Jenn-Air Wall Oven - Instructions

I screwed the light lens into the socket and went beautifully. Better than the original. (I am a retired, 75 yr. old woman).

Removed 2 screws securing bake element, pulled element clear with wires still attached, then removed the wire push terminals. Attached terminals to new bake element and reinstalled. Extremely simple.

1. Turn off the circuit breaker for the oven
2. Open oven and using a phillips screwdriver remove four black screws from under the top panel.
3. Lift panel slightly and remove from oven. Disconnect three wire harnesses.
4. Remove the old display unit by taking out the four screws using a 1/4" nut driver.
5. Install the new display unit using the four screws
from step 4.
6. Hold the top panel close to the top of the oven and attach the three wire harnesses.
7. Hang the top panel on the top of the oven and replace the four screws removed in step 2.
8. Turn on the circuit breaker for the oven.

I removed the single screw on each side of the oven by the hinge to remove the hinge cover plate and expose the hinge opening. I lifted off the glass oven door up and out and set it on my work bench. The door is heavy because its glass so make sure the doors on the way to the garage are open to your work bench area. I installed the cover plates back on so i would not loose the little covers and screws. I removed the screws all around the door and set them in a cup and lifted up the inner part of the door and the hinges are exposed. After removing the screws that hold on the hinges it lifted right out. I cleaned all the glass and set the new hinges in and locked them down with the screws and installed back the inner part of the door to the outer part and returned all the screws back. I then removed they screws on the hinge covers. I did not loose them with 4 kids running around and lifted the door back into the hinge openings and pushed down and it locked in. I then put a little pressure down on the door and removed the little locking pins. I pushed the door all the down and installed the hinge covers back on and it works beautiful. I think the new hinges are better than the set that came with the Jenn-Air wall oven. Thanks Parts Select. Also the new hinges came in 3 days as promised.

At first I called a repairman. He said I needed a relay board replaced but that it was no longer being made. I found this needed relay board on PartSelect.com. Once I received this board within a few days, the repairman returned to install this for me. However, as it turned out he simply removed the old board only to put the same board back in by being careless. When the oven still wouldn't heat he said we should try another part. I said no to this. After he left I determined that the new relay board hadn't been installed but simply looking at it. I then installed this new board myself and the oven now works properly. Who needs these so called "professional repairman" who overcharge, are irresponsible and make you wait hours for their "service".

Removed old part with a pair of pliers and plugged the new part into place.

Very simple and the self cleaning feature works again.

Sunday, four days before Thanksgiving, our oven would not bake properly. A quick check indicated the top element was not working. What to do? Where to get a part in time to fix for Thanksgiving dinner? The answer was easy - PartSelect. I had the part in my hands on Tuesday AM. Oven was fixed in 15 minutes and my wife was baking pies within an hour. All worked well and yes, we had a wonderful trukey dinner. Great service !

The repair was very easy to perform, but the springs in the new hinge were not as strong as the old one. The door would not close all the way unless you held it closed. The hinge looked identical but spring had less tension.

Remove burner knobs, Removed 7 screws from bottom of face plate. Removed screws from 2 alluminum or steel spacers I guess you could call them. I let the Op Panel hang carefully not to stress wires. I marked all wires of the Latch asm. Removed the four screws holding it in and carefully removed the wires. Replaced in opposite manner and self cleaning works. The oven tried to start the cycle but I noticed the latch never triggered. When the function first stopped working I was able to apply slight force to the door and the latch fired. So after replacing the door switch it still failed to work. So latch asm was the official fix. So I have had to replace the latch asm and the Op Panel for being dim. I don't think this model is very good. But Partselect.com is great easy to find parts and good prices. Very pleased with my experience.

First I did it wrong-then I came and read how the 64 yr old lady it and she was spot on. First-turn off power to unit. Take off the 4 screws holding the upper part with the clock in it . (OPen the oven door for access) Then lift up slightly and pull the upper unit out. CLock is right there held on by 4 1/4 inch screws. Remove screws, unplug wiring and reinstall using reverse procedures. Then turn power back on. REady to go

When I removed the bottom bake element and tested it with an ohm meter, it was an open circuit. Once the new one arrived, I simply had to hook up the two leads, screw the cover back on the back of the oven and the job was done.

I didn't. Don't know how to get to light bulb to change it for this specific model

I slide the range out and unplugged it from the outlet. I removed the back of the oven ( 8 screws ) using a cordless drill and phillips bit then with a phillips screwdriver I removed the oven sensor (2 screws) then I installed the new sensor , reinstalled the oven back , plugged the range in , slide it back into place and that was it. This repair took about 10 mins and the oven works perfectly. Thanks !

Took longer to turn off the power than replace the element ,, crazy the appliance company would charge $180.00 for a 3 minute job.

Remove the screws from bottom of door to gain access to the hinge screws. Remove the bottom hinge screws and then open the door to gain access to the top hinge screws. CAUTION after removing the top screws close the door as far as possible while still griping the sides of the door. Pull up on the sides to remove the door from the stove. The springs are fully loaded if you have the door open all the way and try to lift up (like I did) the hinge will spring back and get your finger. Install the new hinge, put the door back into the oven, install all the screws and then remove the temporary rivet that comes installed in the new hinge.