Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JJW8527DDB

JJW8527DDB Jenn-Air Wall Oven - Overview

Get Parts and Repair Help for JJW8527DDB

If you know the wall oven repair part you need, you can browse the list of all parts on the JJW8527DDB, or you can search by name or part description. You can also find your part by where it is located on the JJW8527DDB by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your wall oven. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$39.40

Door Hinge - Left or Right Side

As per the manufacturer, when replacing the hinge, they recommend to also replace the hinge receptical also knows as the bracket. See related parts.

$19.90

Terminal Block

This part is for oven ranges, it connects individual wires and protects the device from electrical surges, voltages, and current. With this part, the house power is connected to the range wire harness. Some symptoms replacing the terminal block could be a solution for are little to no heat when baking, element will not heat and/or it will not start. This part will prevent loosening and will reduce damage caused by corrosion (by two different metals). Refer to the instructional diagram for further replacement guidance and exact placement. You must unplug the appliance before installing this part and wear gloves to protect your hands.

$44.41

Oven Rack

Sold individually.

$24.61

Hinge Bracket - Left or Right Side

$5.10

Screw, 8/18 x 3/8

This screw is sold individually.

$3.02

Screw

This screw is sold individually.

$43.91

Door Gasket

This gasket prevents heat from escaping the oven cavity when in use. It contains all of the attaching clips needed for installation.

$27.30

Broiler Pan

$94.58

Tangential Fan

$64.18

Oven Sensor

This sensor detects the temperature within the oven cavity.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Burned terminal block and filter board

  • Customer: Joseph from Decatur, GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 74 of 157 people found this instruction helpful
Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem. read more

Door would not close tight - light would stay on.

  • Customer: MICHELLE from IMPERIAL, MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Wrench (Adjustable)
  • 15 of 26 people found this instruction helpful
Replaced the hinges, the appliance never really shut 100% and after several year it got worse. Now it is perfect and we don't have any problem with heat up time of oven, used to take extra long to get to desired temp. Should have sent it back in the beginning. read more

oven temp wrong

  • Customer: Alan from Wallkill, NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 7 of 8 people found this instruction helpful
Remove the oven door. Remove 3 self tappers on rear wall of oven to take off a round access panel. Pull out a pre-cut rectangle of insulation. Next I removed the 2 screws holding the sensor in place. Pulling the sensor out a bit told me I was "touching" the correct wires in the SMALL rectangular opening. The wires are not visable and 2 hands do not fit in t... read more