Models > JGW8130DDB Maytag > Instructions

JGW8130DDB Jenn-Air Wall Oven - Instructions

All installation instructions for JGW8130DDB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the wall oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JGW8130DDB
31-45 of 213
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

F-3 error code

  • Customer: Mark from Lake Orion, MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 6 people found this instruction helpful
I removed the two screws that attach the sensor to the oven wall. Then removed to more screws in the back of the oven and took off the rear cover, diconnected the sensor connector and installed the new sensor.

My oven wouldn't light.

  • Customer: Anna from Valparaiso, IN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 6 of 6 people found this instruction helpful
I located the igniter element, and remove the two screws that hold it in place. I then went around to the back of the oven and located the wire, and disconnected it. Then I pulled it out through the oven and removed it. I then replaced it with the new element; pushed the wires through to back of the stove and plugged it in. With that done, I screwed the new igniter element into place. I then put my oven back together; pushed it back into place and turned the gas back on. And presto! my oven lights like new again. I saved myself the costly repairman visit, and the job was easy.

Oven wouldn't heat

  • Customer: Adawel from Brooklyn, NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 6 people found this instruction helpful
First I removed the burner to which the igniter was attached to. Then I attempted to removed the two screws holding the igniter in place. However, these screws proved to be difficult. I called a local appliance repair shop and the person I spoke to explained how the screws were designed to go one way. Any attempt to remove these screws would result in the threading to be stripped and virtually impossible to remove. (I have never heard of these type of screws before) Anyway, he recommended a hack-saw. Well, the hack-saw worked. After that, the replacing of the part was very easy. Igniter works perfectly and now my wife is ready to conquer the bake sales.
This was my first time using partselect.com.
Yes, I will recommend them to other homeowners.
Thanks. A.T

set oven to self clean and the inner glass broke

  • Customer: Garry from Livermore, CA
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 6 of 6 people found this instruction helpful
I removed the door from the oven and set it on towel on the table, and started the repair of the door. I removed the screws one at a time, and one layer at a time. Becareful you need to take the whole door apart, and remember how it goes bact together. In the end it was worth it. The hardest part was getting the right part. I thought I could order the whole door, and found out after several calls they don't sell the whole door. Part Select both times I put in my order had the parts at my door within 2 to 3 days. I also had to return one of the parts and within 2 to 3 days the part was credited to my account

long delay before igniting - long time for oven to heat up

  • Customer: Dace from Arcata, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
The repair was easy. Partselect processed my order quickly and my part was delivered sooner than I expected.

Removing the old igniter was simple. I took off the oven door to create easy access to the oven. I then unplugged the connection and removed the screws that held the older igniter in place. Installing the new igniter was almost as easy. I followed the same steps as above, but in reverse. I accidentally dropped one of the screws, so installation probably took 1 minute longer than removal. :)

I'm a very satisfied customer.

oven wouldnt light or would light inconsistently

  • Customer: Jay from Hubbard, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 6 of 7 people found this instruction helpful
igniter would heat but oven wouldnt come on or would intermittently.opened door a little and lifted it off removed racks and bottom shield removed wingnut and burner shield,removed 2 screws holding igniter ,took off lower shield to allow access to plug,unplugged old one plugged in new one replaced shield and 2 screws holding igniter,put oven back together in reverse order,works like new :) ps if unit not unplugged from wall be careful igniter is hot with electricity and will bite you OUCH!

F3 code, oven wouldn't heat.

  • Customer: Shaun from Kimball, NE
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 11 people found this instruction helpful
First pulled the oven out and noticed how dirty the floor was underneath. Bachelors are BAD housekeepers. Next I removed the oven door (just slides off the hinges) to make it easier to reach in and unscrew the two screws holding the sensor in place in the upper left back of oven. Screws came out easily. Then I removed the back panel by removing the six screws holding it in place. I unsnapped the temp sensor wiring connection, then pulled the probe out from the front (inside the oven). Installed the new probe by feeding the wires and connector through from the front (inside the oven) and attached it with the two screws. Then went to the back again, snapped the wiring connectors together, and replaced the back panel. Then I scrubbed the floor, pushed the range back in place, reinstalled the door, and gave it a test run. PERFECTION! Heated to within five degrees of setting. EASIEST REPAIR JOB I'VE EVER DONE!

Stove wouldn't stay lit and would fire unless the gas was turned on the range top .

  • Customer: Allen from Swengel, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench set
  • 6 of 8 people found this instruction helpful
Removed the drawer and the flash plate underneath .
Unplugged the igniter then opened the & removed the over door . Lifted the bottom plate to expose the burner and igniter . Undo the 2 screws holding the igniter in place . Replace the igniter and reach underneath and plug the wire connecters together . Place all the proper things in their place .. and it was finished ...
The biggest snag I ran into was the one of the 2 screws stripped out when when taken things apart .. but I have taps and found a few new screws and replaced them ......
Quite easy fix .. don't a pay repair man to do it .... !!

Oven would not heat consistently

  • Customer: Leland from Orting, WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
I needed to remove the rear panel to replace the sensor, but unfortunately, that was not the problem. It could have been; but also, it could have been the electronic control, or the gas control valve. This was the cheapest "trial" fix. I did talk to a "Warranty Repair Man", who said that IF it was the electronic control, because of the age of the oven, (13 years) the part would not be available and would need to be fabricated by the manufacture. Even then the cost would approach the cost of a new oven. So, we abandonded the idea of repairs to this one. I guess 13 years is a bit to much to expect of a machine this day and time. Things are made to use-up and throw away. Such is life ! !

Oven temperature lower then setpoint.

  • Customer: Robert from Massapequa, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 6 people found this instruction helpful
After shutting the main valve behind stove. Removed all shelves and rear cover from stove. Unplugged the plug to the sensor. Removed the two mounting screws and pulled the old sensor out. Installed new sensor and plugged it in again. After reinstalling the rear cover and shelves, replugged in power, openned the gas valve behind the stove and tested with soapy water to make sure there wasn't ant developed leaks. Turned on oven with a test thermometer in it. Monitored operation and now oven temperature is roughly 10 to 20 degrees to the setpoint.

Glass on inside of oven door cracked

  • Customer: Tim from Athens, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
I took the oven door apart, pulled out the broken fragments of glass and replaced it with the new glass. I should have taken notes as I took the door apart because it was a bit tricky to remember how all the pieces fit back together.

I was very impressed with how quickly the parts were shipped and the quality of the packing materials to protect the glass as it was shipped.

The F3 error code displayed and beeped during use of the oven and oven shut down.

  • Customer: Debra from Colts Neck, NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
My husband and I began to pull the oven out and I realized that it was too heavy for me to hold. Luckily we were able to get another man to help. Other than that it was easy. Also, it took us awhile to figure out which screws secured the oven into the cabinet. We saved over $1000.00 on a new oven and installation. Kudos to everyone who added their comments! They gave us courage to give it a try.

glass pane was cracked during the cleaning process

  • Customer: Ellen from Shelton, CT
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
needed to completely dis assemble the oven door to get to the inner pane of glass...took some time...I was able to do it on my own...could possibly go a little quicker with two people for a few of the steps...but possible by one...then reinserted the glass pane...and then need to re assemble the door layer by layer...up and working again...would have cost several hundred dollars if need to call a repair person in...this way was the cost of the piece..less than $70 ... and my time...well worth it....thanks

Oven took way too long to preheat . Emitted strong gas odor.

  • Customer: Patrick from Las Vegas, NV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 5 of 7 people found this instruction helpful
I first matched the symptom (very long preheat time/gas odor) with the most likely problem (faulty oven gas igniter). I then wrote the model # and Googled gas oven repair and got to your website. I then located the faulty part within about 5 clicks and proceeded to order the exact part within another 5 or so clicks. I received my order from PartSelest in 2 days and had the oven working with the new igniter in about 10 minutes....Then it dawned on me---"Hey, I should be a Maytag Repair Man."
Thanks for the prompt delivery and the correct installation instructions. I will absolutely use your service again. (Not too soon, I hope !)

Replacing the bulb in the freezer side

  • Customer: Yafa (and David) from Bothell, WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 5 of 7 people found this instruction helpful
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
All Instructions for the JGW8130DDB
31-45 of 213