JGW8130DDB Jenn-Air - Instructions

After reading about my problem, I determined it was the igniter. I immediately ordered one. It came two days later. I took the bottom drawer out and removed the shield. To get to the plug wires, I unplugged the old igniter. I used my power nut driver to take off two threaded screws so igniter could be removed. I then pulled the old igniter out. Plugged new one in and reversed process to install new one. I installed it when I got home from work in less than 30 minutes. all is well. We were looking at buying a new stove for $700.00. I fixed it for less than $60.00. Thanks

removed oven door, removed all shelving....unplugged the electrical cord........unsrewed the igniter(2 screws)removed some of the insulation on back of oven that was covering the wire and plug......disconnected the wire plug...........reversed the process and 15 minutes later I was done............the oven works great.......the new igniter arrived 2 days after I ordered it. thanks

It was necessary to take the decorative glass and metal safety panel off using a screwdriver in order to get to the frame that holds the safety glass. It was hard to slide the new glass into the frame without help from a second person to hold the other pane in place.This was an easy repair to make I would just suggest having 2 people to hole things in place while replacing screws.

1.) Remove door from hinges (open slightly and pull up). 2.) Remove racks. 3.) Remove oven floor to expose burner. 4.) Remove wing-nut and burner cover. 5.) Remove two ignitor mounting screws. 6.) Pull wires and connector through back wall. 7.) Connect new ignitor and mount to burner. 8.) Replace components in reverse order.

I disconnected the electrical power, but not the gas line, and pulled the oven unit away from the wall. I unscrewed the old temperature sensor mount and only realized then the simple configuration: A wire from the sensor runs through the back of the internal oven space to the back of the oven unit through a thin space filled with insulation. The old sensor was easy to disconnect behind the oven unit and pull the old sensor and wire forward through the opening in the oven. The most challenging part was threading the new sensor wire from the oven interior through the back of the oven unit. The instructions and comments provided on-line by previous customers was EXTREMELY helpful. I wish I could do many more household repairs like this!

Ordered the oven sensor. Two screws to remove to replace old sensor. Since this was a slide in unit, you had direct access to the wiring harness. Used the adaptor. Total repair time about 20 minutes. A very easy do-it-yourself project.

easy

First, let me say that the (built-in, electric) oven I was working on was made sold by Kenmore, but the error code and, possibly the repair might apply to many other brands. I was getting a beeping sound and an F1 Error Code on the display of the "clock, timer, control board". On-line research said "you're control board needs to be replaced. I spent days looking for a cheap, new one ($400 for a factory replacement did not appeal to me). Then, I tried "re-setting" the control board. In my case, it took- turning off the power to the oven, turning power back on, pressing and holding "clear". After 30 seconds the beeping stopped. 45 seconds later the error code went away and the oven worked. I opened it up and carefully tested everything with a meter while it was on.It has been working flawlessly for two weeks now. So, the repair took me weeks and also less than two minutes, plus time to give it a check-up. Hope this helps. P.S. I had to say that I used a part in order to post this, I did, but not for this repair.

I opened the door partway to remove the door. Then I removed the bottom heat shield plate by pulling it towards me and lifting it up. I removed the two screws holding on the igniter, then with the the disconnect removed the old ignitor. I plugged in the new ignitor, replaced the screws, replaced the heat shield, replaced the oven door, and was done in ten minutes.

Replacing the vertical mount igniter was very simple. Remove 2 srews and one plug. I did pull out the oven to unplug te igniter. The process could not be easier.

Took off oven door. Took out oven racks. Took out bottom oven cover above igniter. Igniter is held in by 2 screws,took them out with a small socket. Went to back of stove and unhooked white plug in - (part of igniter) Thats it. About as easy as it gets. Just reversed the process putting in the new one. Took about 25 minutes. It would have taken less time but I had a problem with one of the screws. Probably from the heat. The oven is 9 years old.

Open the oven door, take the bottom out. The ignitor is right there!! unscrew it and unplug it... plug in and screw in the new one! Took about five minutes!! Our oven worked again after not working for a year!! Yeah!!

Removed oven door (slides out). Removed side and bottom screws from frame and slid new glass into place. screwed in the 8(or so) screws.

Suspected the igniter, and verified by reading comments on your parts site. The mounting screws were frozen so I used larger screws. Piece of cake! Wa La!

shut off gas and unpluged stove pulled it away from wall removed(2)screws from (top left inside oven)unpluged old sensor in back(left side)and pull old wire thru feed wire from new sensor thru hold pluged in put(2)screws back in done(***used drinking straw and tape to feed new wire thru hole***)