Models > JGS9900BDS > Instructions

JGS9900BDS Jenn-Air Range - Instructions

All installation instructions for JGS9900BDS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JGS9900BDS
31-45 of 88
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

door seal contaminated by a boil-over, not flexible

  • Customer: Rob from Yakima WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
From reading other reviews i thought I would have to dis-assemble the door but when I saw the new part I realized I would not have to, simply pop the beveled clips w/pocket knife and pop in the new seal clips. the ends tucked very nicely, an 80+ yr. old would have no trouble if they had their wits.

One burner would continually keep sparking after burner ignited

  • Customer: Michael from St Louis MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 3 people found this instruction helpful
Removed the small access cover on the bottom of the cooktop by reaching inside and under the cabinets. Removed the module which was held by two hex head screws, unplugged the wires noting the location and color of the wires. Plugged the wires into the new module in the proper locations as noted previously. Attached the module with two screws, and then attached the cover/access plate with two screws. Problem resolved, repair was easy.

Downdraft Blower Failure

  • Customer: Steven from Marshfield MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 6 people found this instruction helpful
Blower motor stopped working and the breaker tripped. Horrible smell! from the somewhere in the oven. Looking at the wiring diagram told me that there was a relay board feeding he motor, but I had no idea where it was, which took a little Internet searching to find it. Finally seeing that it was in the rear I was happy to see that there was enough flexible gas line to pull out the stove enough to check the board, which was fried. I replaced the board and then looked for the reason it smoked and found that the blower motor was shorted (and stank horribly).
It was straighforward to replace, but when I put everything back, NOTHING worked at all - no lights on the control panel, nothing. I then checked the voltage across the terminals and saw 240V and was puzzled until saw that there was no 120V to neutral where the plug connected to the back of the stove. The outlet, however, had 120V to neutral. Since it was a molded plug I thought that was not likey to be a cmmon failure, so after killing th breaker I took off the outlet cover that the stove plugged into and found out that the neutral terminal was intermittent.
The neutral contacts were not grabbing the netral terminal on the plug tightly enough and were a little discolored in one spot. All that moving around of the plug while moving the stove probably moved it just enough not to work at all - that thing was a fire hazard that I'm surprised hadn't been the cause of more damage in a house only 12 years old. Rather than try and clean the termnals and trust bending them to be tighter (and worry about metal fatigue) I spent the $10 so that I could sleep better for a tight new 240V 30A outlet.
Everthing works like a charm now.

broken oven door inner glass pane.

  • Customer: Adam from modesto CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
Remove the door, remove screws from all sides

Remove sides and face of oven door by sliding down from under the oven handle trim.

Remove screws on 2nd light of glass and set aside.

Now you are at the inner door panes. their should be two in an insulated type unit.

Remove the remaining screws from the handle pracket and the permiter frame for the glass/insulation. Remove permiter frame and set aside.

Pull out inner door glass frame. get a pair of pliers and bend tab on frame up so you can pull the frame sightly apart, replace the glass, secure frame tightly around glass slide tab back into reciever slot and bend down ( you may need another person to assist in keeping both lights in the frame while trying to ben tab back in to place)

reassemble door as it came apart carefull not to over tighten the screws, they strip easy.

Front right burner wouldn't lite

  • Customer: Sidney from Saint Francisville LA
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 2 of 3 people found this instruction helpful
The igniiter is made of ceramic and had cracked.
I remove the burner assembly, but couldn't remove the screw holding the igniter. After trying liquid wrench and every available screw driver. I opted to order the complete burner assembly. I installed the new assembly in 5 minutes and it worked great. This is the second ceramic igniter that has cracked on this stove top and both times I've had to replace the whole assembly. For a $1000 stovetop, I expected better quality. I'm just wondering how many times I'm going to have to replace burner assemblies. Each time it's been a different assembly.

Inner glass pane broke during self-cleaning operation

  • Customer: Mark from Abingdon VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.

Electronic ignitor malfunctioned

  • Customer: Richard from Sherman Oaks CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
First reviewed other review on this repair. Disconnected ignitor system from electrical source (pulled plug); removed 2 screws holding casing in place; removed it from the cooktop; & removed additional screw holding ignitor. Replaced ignitor and reversed the process. Done.

Ignitor sparking at bottom, not the top

  • Customer: Edgar from COCKEYSVILLE MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Removed two star screws from the top of the burner, disconnected the wire going to the Ignitor, removed the old ignitor held in with one phillips screw, installed new ignitor and re-installed the burner assembly. Simple!

I lost the cap

  • Customer: Bill from Rochester NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
after I received the cap in the mail, I removed the grillwork and set the cap in place. then replaced the grill and my wife fixed my supper.

Oven was placed on broil with the meat probe too close to the burner.

  • Customer: Matthew from Fort Gratiot MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 7 people found this instruction helpful
I thought the part might not be available. Ordered the part from PartSelect. Couldn't have been easier.

erratic spark from electode,gas would no ignate.

  • Customer: jose from san juan bautista CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Removed the two fastening screws with a small square head screwdriver,lifted the burner head disconnected wire from damaged electrode. To install just reversed the steps,total time less than ten minutes.

Door gasket was hard and brittle from baked-on grease - heat leaking around door

  • Customer: Harlen from Spring Creek NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Waited for my husband to do it, but when he didn't, I tried it. Very simple! Just pulled the old gasket out of the pinch pin holes in the door, then replaced it. Tuck the one end into the hole at the bottom of the door, then match up the little pinch pins on the gasket with the holes in the door - matches up perfectly! Be sure to tuck in each of pinch pins till they sort of "snap" into each hole. Took me 5 minutes, tops. Works great now, no more lost heat around the edge of the door.

electrode sparked but not enough to lite burner

  • Customer: W E from Camden NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 5 people found this instruction helpful
Unscrewed burner assembly and removed wire. Unable to remove electrode screw. Striped head of screw. Tried penetrating oil but no luck. Tried to drill and use easy out bit but ruined burner assembly and had to order new burner assembly. When assembly came it had electrode in place but website does not show electrode with assembly except on one burner. With mail and all it took about a week to fix 2 burners. Returned unused electrode for credit. Overall, cheaper then a service call by far.

Electtrode

  • Customer: Glenn S from Edgewater FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
removed screws that hold burner in place lifted and removed wire connection, reversed attached wire replaced two screws job done,,,

I'd damaged the old door seal

  • Customer: kerry from oldsmar FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Once I saw the spring clips on the new door seal, it was easy to understadn how to remove the old seal and install the new one. Looks nice !
All Instructions for the JGS9900BDS
31-45 of 88