Models > JGS968SEK1SS > Instructions

JGS968SEK1SS General Electric Range - Instructions

All installation instructions for JGS968SEK1SS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JGS968SEK1SS
31-45 of 89
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven not holding a consistant temperature. Found the replacement part easily on you website.Thanks to your photo.

  • Customer: Cindy from Murrells Inlet SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 3 of 6 people found this instruction helpful
First turned off power at breaker box. Pulled stove out to remove the half dozen hex screws on the back panel.(some nuts were stripped)Removed old oven sensor inside oven held by one hex screw and replaced it with the new part. Oven works great now! Repair job was done by husband Mike.

Meat Probe Not Reading Food Temperature

  • Customer: Carl from Vero Beach FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 1 of 1 people found this instruction helpful
A replacement Meat Probe did not correct the problem. Next replaced the Meat Probe Jack which corrected the problem. 1) To replace the Probe jack use 1/2" wrench to remove the nut and washer holding probe to a bracket on the top part of oven, just inside the oven door.
2) Unscrew two screws under the lip of the top burners, raise up the whole top, using a short stick to hold-up the top while you access the Probe Jack.
3) With your fingers gently follow 2-braded jack wires laying ontop of the insulation batting. The 2 wires run under the batting to the loose Jack. Carfully remove the old probe jack and install the new jack and secure with 1/2" wrench.
4. Pull stove out so you can get behind, unplug the stove and remove metal paneling covering back of control Panel. Locate the two braded wires running from front of oven over batting to a whole in rear oven wall, just below control panel. Replace new wires from the new meat probe jack, following the same route to back of stove. Carefully pull wires back and trace location to back of control panel. Unplug the old jack and replace the new wires, being careful not kink or fray the new wires. Replace back panel and plug in stove, lower and secure the 2 screws holding the burner top down. Check Probe on front of stove to make sure your getting a probe reading. Your done in a few minutes.

drwer slide under stove broke off.

  • Customer: paul from sewell NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
recieved part the next day. looked different but I followed instructions and the part worked perfect.

After my housecleaner had been here, I noted that 2 of the little rubber feet were missing from the top grates.

  • Customer: Anne from Jacksonville FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
I was pretty upset as the grate wobbled, so I went on line and looked for GE Profile parts. To my amazement, I found the little rubber feet quite easily, and within 2 days they were here at my home. I simply had to stick them in the holes; however, I noted that they did not fit real tight, so I removed them and shot a little glue on them, and they have been in place ever since. Thanks to you guys, I am a happy camper now!!!

Broken rear drawer support

  • Customer: Jesse from Knob Noster MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 2 people found this instruction helpful
Installed the new brackets at the back of the drawer with the 2 screws provided. The new rear mount design is much better than than the old side mount.

very easy

  • Customer: ROBERT from CYPRESS TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
there were no grate pads so it was easy to add them.

Rubber Grate foot worn or missing.

  • Customer: Terry L from Puyallup WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Replaced worn or missing Grate Foot with new ones. Took less than 5 minutes.

The storage drawer came without supports.

  • Customer: Dock from Aurora CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 2 people found this instruction helpful
I just removed the drawer and installed the rear supports as instructed on paper included with the part.

Sparking at 2 different burners all by themselves

  • Customer: paul from las vegas NV
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 3 people found this instruction helpful
Replaced Spark Module and adjusted igniters

Malfunctioning Regulator

  • Customer: Jesse from Lubbock TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Wrench set
  • 1 of 3 people found this instruction helpful
I replaced the regulator because it would close off when not in use. The regulator would not allow gas to flow for 15-45 seconds after 1 or more valves were opened. Everything functioned fine after the gas started flowing, but after a few minutes of having all burners off, you would have to wait for the regulator to open up when you needed to cook again. It was not the biggest problem in the world, but my wife complained like it was. The fix was easy and not to expensive, especially when you consider how much she was willing to pay the repair man. Hands on work was about 10 minutes. Gathering tools and teaching my son what I was doing took up the bulk of the time.

Grate foot bdroke off allowing grate to scratch cooktop

  • Customer: John from Tijeras NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Used scribe to remove grate foot plug still in grate inserted new foot.

Oven will not heat

  • Customer: Joseph from Homosassa FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
As many people have encountered, my oven would not heat but the igniter would be bright orange and glow! Over time, the igniter wears and degrades causing oxidation to the surface. This cause the igniter to fail and operate at a lower current level, below 2.8 amps! Normal igniters operator over 3.0 to 3.1 amps. When is happens, a low current igniter does not have enough input to the control valve to tell the valve to open to allow gas to flow over the igniter to light the oven, thus heat the oven! This has got to be the NUMBER one reason for an oven not heating!

The Grate foot is to big for the hole.

  • Customer: Harold from Broadalbin NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I had to drill the hole to a larger size to enable the foot to fit.

The Grate Foot was deteriorated on several sections for my cook top. The hardest part was finding the right part.

  • Customer: Chelagh from Fredericksburg VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
Nothing technical.

Leaking from front door

  • Customer: Gene from Simi Valley CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 7 people found this instruction helpful
First remove the screws around the inside perimeter of the door. These require a special hex driver. Take off the inside plastic liner of door.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The Insulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.
All Instructions for the JGS968SEK1SS
31-45 of 89