Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JGS8850BDW

JGS8850BDW Jenn-Air Range - Overview

Get Parts and Repair Help for JGS8850BDW

If you know the range repair part you need, you can browse the list of all parts on the JGS8850BDW, or you can search by name or part description. You can also find your part by where it is located on the JGS8850BDW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for JGS8850BDW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$50.37

Oven Igniter - Vertical Mount

This broil igniter assembly comes with its own metallic mounting bracket and a 7-inch-long dual wire lead with a plastic plug. This part will need to be repaired if your oven eleme...

$18.93

Burner Electrode

This is a burner electrode for your oven, range, or stove. This part has a male spade. It helps your burner ignite by creating a spark, producing a flame, and lighting the surface burner. If your burner will not heat properly, you may have to replace the burner electrode. Your electrode is located under your burner. This is an OEM replacement part that will be sourced from the genuine manufacturer. This part measures less than 1.5 inches long. It is sold individually. If you need a wire lead to complete your repair, you can purchase them locally.

$24.22

Short Oven Sensor Kit

The temperature sensor on your oven detects the temperature within the oven cavity. If you notice your oven is too hot, not hot enough, or does not heat evenly, the short oven sens...

$3.02

Screw

This screw is sold individually.

$4.15

Grate Foot

Sold individually. Must be held in with adhesive. Part # PS972585.

$5.52

Screw

Sold individually.

$44.96

Door Gasket

The oven door gasket on your range functions as a seal between the warm interior of your oven, and the outside. It prevents heat from fleeing your oven when the door is closed. Bef...

$51.52

Oven Rack

This is a replacement oven rack and it is designed for use with ranges and ovens. This is a genuine OEM replacement part. The rack provides a level and stable surface for cookware inside of your appliance. Installing the new rack is simple, you slide it into the pre-existing tracks in your oven. It measures approximately 23 inches wide by 16 inches deep. This replacement part is made of metal and it is sold individually.

$45.18

Burner Head with Electrode

$3.02

Screw, Igniter

This screw is sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven wouldn’t heat up properly

  • Customer: James from Berwick, ME
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 216 of 241 people found this instruction helpful
My oven has two igniters so I needed to determine which one was the problem.

Using the amp/multi meter I tested the connection between the igniters and the valve, with the oven turned on, to find the bad igniter. Depending on the model of stove you have, the amp reading you need for a properly functioning igniter will vary. My lower igniter read ... read more

F1 code - gas over would not heat.

  • Customer: george from birmingham, AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 142 of 152 people found this instruction helpful
Repair tech checked oven and said the control panel was bad and needed to be replaced. The new control panel would cost over $450.00! I found that the oven sensor was bad and replaced it for $30.00. The old oven sensor had failed following a self cleaning cycle. I found that the wires coming out of it were burnt.

Replacing the oven sensor was ... read more

Ignitor stopped working on gas cooktop

  • Customer: Jeff from Lake Orion, MI
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 62 of 62 people found this instruction helpful
As others reported, there are 2 torx screws that need to be removed so that the burner element can be removed. One came out with a little effort, the other one did not as it was corroded. After breaking a torx bit, a second torx bit succeeded in breaking off the screw head. This then required a drill to drill out the broken shaft and then rethreading the s... read more