Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JGR8750ADW

JGR8750ADW Jenn-Air Range - Overview

Get Parts and Repair Help for JGR8750ADW

If you know the range repair part you need, you can browse the list of all parts on the JGR8750ADW, or you can search by name or part description. You can also find your part by where it is located on the JGR8750ADW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for JGR8750ADW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.91

Light Bulb - 40W

Sold individually.

$31.07

Flat Style Oven Igniter Kit

The flat style gas oven igniter included in this kit has a body length of 3-3/4 inches. This kit comes with all of the pieces you need to replace longer ceramic igniters, though this kit can also replace short igniters. This igniter has an amperage range of 3.3 - 3.6 and does NOT replace round style oven igniters.

$16.43

Top Burner Igniter

This top burner igniter comes with a mounting bracket.

$23.99

Short Oven Sensor Kit

This temperature sensor detects the temperature within the oven cavity.

$66.33

Inner Door Glass Pane

Glass only.

$21.91

Door Trim Kit - White

This part includes the trim kit which is now in 3 separate pieces. It would cover the bottom and sides of the door.

$4.63

Storage Drawer Wheel and Shaft

This wheel and shaft is used to open and close the bottom storage drawer of a range/stove.

$83.03

Double Drip Pans - Set of 2

These pans are only available in Gray. Black and Bisque are no longer available. The only option is Gray.

$5.15

Insulation

This strip of insulation is located within the oven door.

$50.68

Bake Burner

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven would not work but the Broiler did

  • Customer: James from Ferndale, MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 248 of 274 people found this instruction helpful
The oven had been working intermittently for a while and after repeated threats of starvation from my spouse I finally took a look even though it was summer and the grill was working fine. The Igniter would glow red when the oven was turned on but the gas would not flow to it no matter what the temperature setting. I searched online and found this site that ... read more

A burner wouldn't spark strongly enough to light the gas.

  • Customer: Matthew from Brookfield, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 135 of 150 people found this instruction helpful
Replacement of these burners is very easy. You just twist the burner counterclockwise a quarter turn and pull it out. (You may need a big wrench if the range is very old.) Once out, just pull the two wires off and push them onto the new burner. Crimp them on with pliers if they're loose -- mine were. Twist the burner back on.
If the gasket under the bu... read more

F1 code - gas over would not heat.

  • Customer: george from birmingham, AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 119 of 128 people found this instruction helpful
Repair tech checked oven and said the control panel was bad and needed to be replaced. The new control panel would cost over $450.00! I found that the oven sensor was bad and replaced it for $30.00. The old oven sensor had failed following a self cleaning cycle. I found that the wires coming out of it were burnt.

Replacing the oven sensor was ... read more