Models > JGP975SEK2SS > Instructions

JGP975SEK2SS General Electric Cooktop - Instructions

All Instructions for the JGP975SEK2SS
1 - 15 of 49
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The cooktop had a shorted out burner control.
Unpllug the cooktop and turn off the gas supply. Remove the grates and burners.(they just lift out). Using a torx screwdriver, remove all the torx screws below where the burners sit. There are three screws per burner, except the power burner which has only two screws. Genly lift the stainless steel cooktop, separating it from the rest of the enclosure. Hold the electrodes with one hand, while gently twisting and pulling the wire connector off. Now, remove the aluminum covered foam piece. You will now have acess to the wiring harness assembly. Disconnect the quick connectors and replace with the new assembly. Re-assemble in the reverse order and you're done. About 1.5 to 2 hours. Good Luck
Parts Used:
Igniter Harness Switch Top Burner Spark Electrode Grate Foot
  • FRANK from MEMPHIS, TN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
70 of 92 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Grate Foot had worn out
A rubber grate foot on my range top had worn out. I pulled the worn foot out and installed the new grate foot with no tools or accessories. Good as new! Now I don't have to worry about the grate scraping my range top and scratching the paint. I also ordered extras so I won't have to wait if another wears out.
Parts Used:
Grate Foot
  • Kathryn from Star City, AR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
24 of 30 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner would not lite
openend stove top disconnected wire pushed out old sparker inserted new one closed lid game over
Parts Used:
Top Burner Spark Electrode
  • Glen from Kenner, LA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
23 of 33 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner would not light properly and flame uneven around the burner
determined that the top of the burner was melted and malformed. Repair was simple: lifted off the damaged burner and slipped the new one in place.
Parts Used:
Burner Head - Large - 12K
  • Bret from South Haven, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
9 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Our burner caps had started chipping.
Was able to see the exact part with easy to read schematic so I knew I was ordering the right part. Then just switched out the old for the new. Looks like a new cooktop except for the scratches in the stainless, but we are working on that! Thanks!
Parts Used:
Burner Cap Burner Cap - Black - Medium - 9500 BTU Burner Cap - 5000 BTU - Black
  • Kim from Santa Rosa, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
12 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Change bad/broken igniter on gas stove top burners
Very simple repair with no tools required. Turn off power to stove. Remove grates, remove burner, pull old Top Burner Spark Electrode up being careful not to jerk it up hard - wiggle if necessary, unplug wire from old electrode, plug wire into new electrode making sure it fits snug - if not, squeeze it closed a little at a time until it fits snug, push new igniter into place being careful not to force it and crack the ceramic body. Install burner being careful not to damage the electrode, Install grates. Turn power back on and test to make sure it works. It took me all of 15 minutes to change 2 burner spark electrodes. The only bad thing about this repair is that the shipping costs as much as the parts.
Parts Used:
Top Burner Spark Electrode
  • James from Kaplan, LA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
ignitor wouldn't spark
Compressing the spring to apply the retainer clip was some what of a challange. But, everything went fine. Mission accomplished.
Parts Used:
SPRING IGNITER WASHER IGNITER ELECTRODE TOP Burner Cap - Black - Medium - 9500 BTU
  • David from Cherryvale, KS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
11 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed To Replace Burner
Took longer to open the box.
Parts Used:
Small Burner - 5K
  • Robert K from York, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burnt burner
Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.
Parts Used:
Burner Head - Medium - 9500
  • Janine from Wind Gap, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
7 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
After my housecleaner had been here, I noted that 2 of the little rubber feet were missing from the top grates.
I was pretty upset as the grate wobbled, so I went on line and looked for GE Profile parts. To my amazement, I found the little rubber feet quite easily, and within 2 days they were here at my home. I simply had to stick them in the holes; however, I noted that they did not fit real tight, so I removed them and shot a little glue on them, and they have been in place ever since. Thanks to you guys, I am a happy camper now!!!
Parts Used:
Grate Foot
  • Anne from Jacksonville, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner on stove not working correctly
Order parts and installed - no tools needed - completed repairs less than 1 minute
Parts Used:
Burner Head - Medium - 9500
  • Trevor from Eldersburg, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner caps began to chip
I removed the two range grills. Then I removed the two chipped burner caps, and replaced them with the new burner caps. I then replaced the two range grills.
Parts Used:
Burner Cap Burner Cap - 5000 BTU - Black
  • Anne from Plainview, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
5 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original grates that came with my cook top had bowed due to the weight of my pans when cooking which caused everything to slide to the back of the pan when cooking.
The grates arrived individually packaged in bubble wrap and in their own box plus those boxes were put in another box with bubble wrap. Very impressed with their shipping technique! The grates fit my cook top perfect! Nothing but good things to say about Part Select and their customer service. Awesome!!
Parts Used:
Double Grate
  • Patti A. from Dallas, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
THE OLD BURNER HEAD WAS NOT TURNING ON PROPERLY AND THE GAS CAME OUT UNEVEN.
I JUST EXCHANGED THE BURNER AND BURNER CAP.
Parts Used:
Burner Head - Medium - 9500 Burner Cap - Black - Medium - 9500 BTU
  • Astrid from MORAGA, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gas range igniter was making a clicking sound every 3 to 5 minutes, as if it was trying to ignite one of the burners.
Unplug the range from its wall socket to avoid electric shock. The various range parts that support a pot or frypan are easily lifted off their perches, exposing the small white igniter. The only moderately difficult aspect is wiggling the igniter out of its retainer. The electric wire leading into it then can be pulled out and fed into the new igniter with a push. Replace igniter in its retainer, then replace the range parts you removed to expose the igniter and plug the range back into the wall socket. Piece of cake.
Parts Used:
Top Burner Spark Electrode
  • Wesley from FRANKLIN, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JGP975SEK2SS
1 - 15 of 49