Models > JGP975SEK2SS > Instructions

JGP975SEK2SS General Electric Range - Instructions

All installation instructions for JGP975SEK2SS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JGP975SEK2SS
1-15 of 30
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The cooktop had a shorted out burner control.

  • Customer: FRANK from MEMPHIS TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 27 of 36 people found this instruction helpful
Unpllug the cooktop and turn off the gas supply. Remove the grates and burners.(they just lift out). Using a torx screwdriver, remove all the torx screws below where the burners sit. There are three screws per burner, except the power burner which has only two screws. Genly lift the stainless steel cooktop, separating it from the rest of the enclosure. Hold the electrodes with one hand, while gently twisting and pulling the wire connector off. Now, remove the aluminum covered foam piece. You will now have acess to the wiring harness assembly. Disconnect the quick connectors and replace with the new assembly. Re-assemble in the reverse order and you're done. About 1.5 to 2 hours. Good Luck

Grate Foot had worn out

  • Customer: Kathryn from Star City AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 11 people found this instruction helpful
A rubber grate foot on my range top had worn out. I pulled the worn foot out and installed the new grate foot with no tools or accessories. Good as new! Now I don't have to worry about the grate scraping my range top and scratching the paint. I also ordered extras so I won't have to wait if another wears out.

burner would not lite

  • Customer: Glen from Kenner LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 13 people found this instruction helpful
openend stove top disconnected wire pushed out old sparker inserted new one closed lid game over

burner would not light properly and flame uneven around the burner

  • Customer: Bret from South Haven MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 7 people found this instruction helpful
determined that the top of the burner was melted and malformed. Repair was simple: lifted off the damaged burner and slipped the new one in place.

Burnt burner

  • Customer: Janine from Wind Gap PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.

ignitor wouldn't spark

  • Customer: David from Cherryvale KS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 10 people found this instruction helpful
Compressing the spring to apply the retainer clip was some what of a challange. But, everything went fine. Mission accomplished.

Needed to replace burner

  • Customer: Robert K from York PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
Took longer to open the box.

burner caps began to chip

  • Customer: Anne from Plainview NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
I removed the two range grills. Then I removed the two chipped burner caps, and replaced them with the new burner caps. I then replaced the two range grills.

feet keep falling off

  • Customer: Richard from Stratham NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
Inserted the grate foot into the spot provided; after consulting the parts manuel to insure I was using the proper procedure.

I do use silicone to help hold the foot but it still won't hold

After my housecleaner had been here, I noted that 2 of the little rubber feet were missing from the top grates.

  • Customer: Anne from Jacksonville FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
I was pretty upset as the grate wobbled, so I went on line and looked for GE Profile parts. To my amazement, I found the little rubber feet quite easily, and within 2 days they were here at my home. I simply had to stick them in the holes; however, I noted that they did not fit real tight, so I removed them and shot a little glue on them, and they have been in place ever since. Thanks to you guys, I am a happy camper now!!!

Burner had uneven flames

  • Customer: Akshay from Bridgeton NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 4 people found this instruction helpful
Too easy a five year old could do it

Original grates that came with my cook top had bowed due to the weight of my pans when cooking which caused everything to slide to the back of the pan when cooking.

  • Customer: Patti A. from Dallas TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
The grates arrived individually packaged in bubble wrap and in their own box plus those boxes were put in another box with bubble wrap. Very impressed with their shipping technique! The grates fit my cook top perfect! Nothing but good things to say about Part Select and their customer service. Awesome!!

Burner on stove not working correctly

  • Customer: Trevor from Eldersburg MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Order parts and installed - no tools needed - completed repairs less than 1 minute

very easy

  • Customer: ROBERT from CYPRESS TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
there were no grate pads so it was easy to add them.

Our burner caps had started chipping.

  • Customer: Kim from Santa Rosa CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Was able to see the exact part with easy to read schematic so I knew I was ordering the right part. Then just switched out the old for the new. Looks like a new cooktop except for the scratches in the stainless, but we are working on that! Thanks!
All Instructions for the JGP975SEK2SS
1-15 of 30