Models > JGP636WEV7WW

JGP636WEV7WW General Electric Cooktop - Overview

Get Parts and Repair Help for JGP636WEV7WW

If you know the cooktop repair part you need, you can browse the list of all parts on the JGP636WEV7WW, or you can search by name or part description. You can also find your part by where it is located on the JGP636WEV7WW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your cooktop. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the JGP636WEV7WW [Viewing 2 of 2]

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$24.77

Surface Burner Spark Electrode

This part helps your burner ignite and produce flame.

Order within the next 8 hrs and your part ships today!
$17.73

Large Burner Drip Bowl

Order within the next 8 hrs and your part ships today!
$19.21

Medium Burner Drip Bowl

This burner drip bowl is sold individually. It is white on the top side, and black underneath.

Order within the next 8 hrs and your part ships today!
$16.45

Small Burner Drip Bowl

This burner drip bowl is sold individually. It is white on the top side, and black underneath.

Order within the next 8 hrs and your part ships today!
$2.79

Screw

Sold Individually.

Order within the next 8 hrs and your part ships today!
$5.98

Single Liquid Propane Orifice Spud - Medium Burner

Sold Individually. Order quantity needed.

Order within the next 8 hrs and your part ships today!
$1.48

Screws - Package of 12

Order within the next 8 hrs and your part ships today!
$6.62

Natural Gas Orifice Spud

This orifice spud changes the burner from liquid propane to natural gas. This orifice is sold individually. Size: 1.07mm

Order within the next 8 hrs and your part ships today!
$28.63

Gas Pressure Regulator

This comes set from the manufacturer for Natural Gas. It also includes the conversion to Liquid Propane. This valve automatically cuts off the flow of gas at a certain pressure.

Order within the next 8 hrs and your part ships today!
$16.87

Foam Rubber Tape

Order within the next 8 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Burner igniter needed to be replaced

  • Customer: Thomas from Bloomsbury NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 18 of 33 people found this instruction helpful
Assumed the entire top of the range would have to be lifted off. Removed the three screws inside the top of the over door and then noticed the two screws holding the dish around the burner. They were tight and required WD-40 and then a sharp tap and came off.
Important: Notice the direction your old igniter is plugged into the wire. It is not clea... read more

The porcelain had chipped on the burner bowls

  • Customer: Paula from Seal Beach CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 8 people found this instruction helpful
Removed the two screws holding the porcelain burner bowl. Disconected the electric igniter by removing the "w" clip on the underside of the bowl. Then disconnected the igniter from the electric supply cord. Reverse these directions using the new urner bowl.
Really easy. read more

Drip pans needed to be replaced.

  • Customer: Steve from Broken Arrow OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 11 people found this instruction helpful
Simiple repair. Determined drip pan size (sm, med., lg.) removed 2 screws holding drip pan, placed gasket around new drip pan and installed. Repaired took less than 5 minutes. read more