Models > JGP336BEV2BB > Instructions

JGP336BEV2BB General Electric Range - Instructions

All installation instructions for JGP336BEV2BB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JGP336BEV2BB
16-24 of 24
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Burners began to fail to ignite.

  • Customer: michael from new hope PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Removed six screws on the back panel. Just switched six wires from the old to the new module. Stove burners work perfectly now.

The tempered glasstop on my range shattered.

  • Customer: Julie from Libertyville IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I had to unscrew the screws and then disconnect the knob where the gas wires go. Then, I set the glass top down and screwed the black "catch" plates back in place. It wasn't very hard.

Knobs stripped-would not turn gas on

  • Customer: Dennis from Birmingham AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Swapped out old knobs for new ones. Glad I was able to get original parts.

Ignitor on one burner worked intermittently

  • Customer: Paul from Pflugerville TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Cut off power to the cook top and confirm that power is actually off. In my case, this involved turning off a cicuit breaker. Remove all burner control knobs by pulling straight up. Lift off all grates, burner caps and burner heads. Remove two phillips head screws from each burner bowl. Pry each burner bowl up and unhook the ignitor wire. I labeled the wires to make sure I got them hooked back up right. Remove the four burner bowls by lifting them off. Make sure you remember where each goes so you can reinstall them in the right places. Pry up the glass cooktop and lift it off. I took the cooktop ouside and gave it a good cleaning. This plus cleaning around the cooktop and cleaning the burner bowls is what took most the time. Lift the defective switch off and disconnect the two wires. Align the flat in the new switch to the off position. Reconnect the wires and install the new switch on the valve stem. Reinstall the cook top. Reinstall the burner bowls making sure to reconnect the ignitor wires. Reinstall the burner heads, burner caps, grates and knobs. Turn the power back on and make sure everything works correctly.

Left rear burner would not light

  • Customer: Fred from Laguna Hills CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Began by removing the front panel where the range handles are located. There were 7 screws located under the panel which required opening of the oven hood. All of this removal was a waste of time, because the range top was on hindges. The only thing holding ithe range top down was the accumulated grease and oil along the edges. I used a screwdriver to sperate the range panel. There were side supports to hold the the top up, like a car hood support. Replacing the electrode was a snap after that. Overall, it took less than 30 mins but it would have taken less than 10 if I hadn't removed the front panel.

no spark at burner

  • Customer: James from Jenison MI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove grates,pans and disk. Remove allen screws at each burner. Take a flat blade screwdriver and press in on tabs on each side of front of stove to depress keepers and lift top up. Remove wire, and keeper on bottom of electrode. Reverse for install.

only back burnners lit

  • Customer: Howard from Lorain OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Rremoved the back cover, changed the wires from one ignighter to the other, removed the old ignighter, and snapped in the new one, put four screws back on cover, and pushed stove back into place, turned on all burners several times to make shure eveything worked!!!

change over from natural to lp gas

  • Customer: marcus from gastonia NC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
i removed the cover over hole that holds the orifice used a 7mm nut driver with butyl rubber tape stuffed inside nut driver, this stuff is sticky and holds orifice in place while positioning over hole.total time about 3 minutes. they worked perfectly.

REPLACE 4 WHITE BURNER DISHES ,4 GREY BURNER GRATES AND CAPS. WITH BLACK.

  • Customer: Antonio from Manteca CA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
THERE WERE 3 ? TYPES OF BLACK BURNER DISHES AND 3 TYPES OF BURNER CAPS. THE INFORMATION I COLLECTED DID NOT HINT ABOUT THE DIFFERENT SIZES. WE SENT BACK 2 CAPS FOR THE PROPER ONES. MEANTIME 3 OF THE DISHES WERE ON BACKORDER. I INSTALLED THE ONE DISH I HAD. LATER THE 3 BACKORDER DISHES ARRIVED. I BEGAN TO INSTALL THEM WHEN I DISCOVERED I NEEDEED MORE THAN ONE SIZE. I AM A RETIRED AEROSPACE ENGINEER. I HAD TO USE MY FILE AND HAMMER TO FIT EXPERIENCES TO MAKE UP FOR MY PARTS ORDERING DEFICIENCY. THE NEW DISHES, MOUNTING HOLES, WERE DIFFERENT THAN THE ONE I HAD PREVIOUSLY INSTALLED . SO IN ORDER NOT TO RETURN THEM AND WAIT AN ADDITIONAL FEW WEEKS , I FILED THE MOUNTING HOLES SUFFICIENT TO BE ABLE TO MOUNT THEM. THEN I PUT THE NEXT PART ON AND DISCOVERED THAT IT DID NOT FIT THE NEW LOCATION OF THE IGNITER . I FILED THE APPROX 1/2" DIA HOLE FROM ROUND TO A "D"CONFIGURATION ON 3 PARTS , THAT ALLOWED THE IGNITER TO FUNCTION IN TWO OF THE NEW LOCATIONS . THE FOURTH AND SMALLEST BURNER REQUIRED AN ADDITIONAL 1/4" SPACER TO MOVE THE GAS SUPPLY RISER CLOSER TOTHE IGNITER. THE BURNERS ARE ALL WORKING AS NEW. NO FIRE HAZARDS.
MY WIFE DOES NOT KNOW THE GOOFS I MADE. I HAD TO USE SOME INVENTIVE METHODS AND I'M STILL HER HERO.
I WOULD CAUTION ALL DI IT YOURSELF PEOPLE TO BECOME VERY FAMILIAR WITH THE PARTS THEY NEED. THEY MAY ALL LOOK THE SAME TO THE NOVICE BUT THERE ARE SLIGHT DIFFERENCES THAT SHOULD REQUIRE REPLACEMENT AND COULD TAKE AWAY YOUR HERO STATUS.
All Instructions for the JGP336BEV2BB
16-24 of 24