Models > JGD8430ADB > Instructions

JGD8430ADB Jenn-Air Cooktop - Instructions

All installation instructions for JGD8430ADB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JGD8430ADB
61-75 of 104
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

broken knob to stove top.broken by me

  • Customer: Scott from Boca Raton FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 19 of 609 people found this instruction helpful
First went to an appliance distrib. store.They would have to part.Was qouted a price.Wenthome and went online to partselect.com and saved 40% even with shipping.Got the part the next day!Pulled old knob off and pushed new knob on.Thank you for making it easy.

Burner knob was cracked where it meets the shaft

  • Customer: Susan from Wilmington MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 19 of 609 people found this instruction helpful
Took broken knob off and slid the new one on. DONE!!!

I had a broken air vent knob on my range top.

  • Customer: Joan from Davis CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 19 of 609 people found this instruction helpful
The part was here three days after ordering and I put it on with no tools in less than a minure.

broken burner knobs

  • Customer: Delton from Nevada MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 19 of 609 people found this instruction helpful
So simple -- any monkey could do it. Pull off the old knobs and push on the new.

Knobs split and will not turn on burners

  • Customer: Daniel from Charlotte NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 19 of 609 people found this instruction helpful
Removed old knobs and replaced with new ones.

previous owner broke knobs by not pushing down to turn on, then leaving the D rings on when they switched them. Only 1 burner was operating

  • Customer: kim from Pahrump NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 18 of 608 people found this instruction helpful
I carefully pulled the 3 D rings that were left on the posts of the burner controllers with a pair of needle nosed pliers, made sure there was nothing on the controller posts, then put the new knobs on. Make sure there are no D rings on the oven knob posts, 2 of the knobs were fine, they just didn't have D rings in them. Partselect was great. Items were received within 2 days. I would definately recommend them.

Burner knob got stripped out, taking them off and on...

  • Customer: Marv from Bella Vista AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 18 of 608 people found this instruction helpful
Got on line and ordered part and lined up flat side of inside of knob and slid it on... That simple... The person who put them on after cleaning stove never knew there was a flat side inside knob.. We never stop learning, do we???

replace burner knob

  • Customer: Jacob from Coral Gables FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 18 of 608 people found this instruction helpful
with my own two hands, just slip it on--- no story.you folks came through quikly with no complications and deserve a compliment.

burner porsclend was cracked and would not light

  • Customer: edward from nanticoke PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
removed grate and cap.unscrewed burner plate.disconnected spark wire and replaced with new part.fired it up .now it workes again.

Former Burner Knob was broken

  • Customer: FRED from Flower Mound TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pulled old ones off and replaced new ones by pushing them on the spindles. Very easy!

The female D stem fitting of the control knob cracked, we could not turn on / off or control temperature to that heated area.

  • Customer: Richard from Harrisville RI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
We replaced the control knob with an exact replica from PartSelect at a very reasonable price – Thank you.

Burner knob socket was broken

  • Customer: Yosh from Mill Creek WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
pull out the old knob and replace with a new one.

Burner Head was leaking gas from side

  • Customer: Earl from Iuka IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I lifted the burner tray from stove turned it upside down then removed six small screws from side of cover pan then I removed the cover then I removed the screws from the back of the old burners and igniter.Then I turned the old burner counter clockwise and it lifted out easly. the igniter is removed with no problem. The new burner is put in place and turned clockwise to lock in place.Then replace then the gas tubes and igniter and igniter wire then put tray cover on.

burner ignator split--

  • Customer: KARL from OCEAN NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
unscrewed old ignator---replaced w new--done deal!!!!

plastic split

  • Customer: Walter from Spring TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
remove knobs from pkg, remove broken knobs from range insert new knobs wallah done.
All Instructions for the JGD8430ADB
61-75 of 104