Models > JGD8348CDP > Instructions

JGD8348CDP Jenn-Air Cooktop - Instructions

All installation instructions for JGD8348CDP parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JGD8348CDP
31-45 of 67
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Grease filter was torn and bent

  • Customer: Brent from Rancho Santa Fe CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I just lifted out old filter, and put in new one.

The original grease filter was damaged in our dishwasher (it is quite fragile) and needed to be replaced.

  • Customer: Martyn from Middletown OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover

Needed to replace the grease filter!

  • Customer: Colette from Annapolis MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Followed the directions. Piece of cake!!

vent fan cloging up

  • Customer: JAMES from McALESTER OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
old filter fell into from removing and cleaning,
removed cover pulled out filter ,replaced it with new one.

Filter needed replacement. Old one was falling apart.

  • Customer: Sophie from Warrenton VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Removed old filter, dropped in the new one.
(This really was not a "repair")

Old filter couldn't be cleaned

  • Customer: William from Goshen NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
This was a no-brainer: old filter out, new filter in. In addition to replacing an old, greasy filter, I found that the exhaust fan now draws cooking fumes much more efficiently. So why did I wait the 6 years since we moved into this house to do this???

ordered a new filter for the exhaust fan

  • Customer: Marijo from Bennett IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
The filter came and it was bent out of shape on 2 sides. My husband carefully tried to bend it back into shape. It is very flimsy and is not made as well as the one that was being used that was probably several years old. I did not want the hassel of returning the filter and trying to get a new one sent.

Change the Oil/Grease Filter

  • Customer: Yong from Houston TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.

rotten filter for down draft vent

  • Customer: Craig from Ashburn GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
How I did the repair is no consequence. The service of easily finding the part on your site is GREAT! and the shipping time more than reasonable! Thanks!

old yucky filter

  • Customer: Diane from Flower Mound TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
Thanks, have been looking for a replacement for this dinosaur filter forever. It is great!

Intermittent but rare spark when I went to start the rage: spark module definitely was toast or on its way out

  • Customer: Bronius from College Station TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 15 people found this instruction helpful
The trickiest part was locating the elusive spark module. I am not certain I took the best route, but not considering all the wrong routes in trial and error, it was the most expedient. Certainly there must have been a single something to remove to get to this frequently faulted part..

Anyhow, thanks to the great part, the stove works really well again.

Holes in the air filter of our Jenn-Air grill

  • Customer: Janice from Ocala FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simply pulled the old filter out and put the new filter in.

broken insulator for top burner igniter

  • Customer: Paul from Block Island RI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I have a Magic Chef gas stove, The top burner came off with ease, just a quarter turn then pull up to expose igniter. Only two wires to remove and two phillips head screws to remove to release igniter. I was done in 5 minutes.

Replacement of a Dead Spark Module

  • Customer: Cor F. from Pasadena TX
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The spark module pulses a stepped up voltage to all four burner sparks at the same time regardless of which burner you want to ignite. I read that this part lasts about 10 years. I don't cook much and it lasted 13 years. On my Magic Chef the part is behind the right side wall panel. Lift the range top,remove all the screws that hold the right side panel in place. This replacement can done without opening any gas fittings.

Only two burners lit

  • Customer: Inga from Petaluma CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed old igniter set replaced with new one. Hardest part was using the screw driver to removing the backing. Saved us having to buy a new stove since we just bough the house.
All Instructions for the JGD8348CDP
31-45 of 67