JGD8130ADS Jenn-Air Cooktop - Instructions

Shut off gas supply
Pulled stove away from wall removed spark ignigtor box .
Installed new one .
No problem.
Good for another 10 years

remove grate - flip upside down - be sure holes are clean and dry - using toothpick, swab some RTV sealant into the holes and a bit on the pads ... insert pads till they seat - be sure to hold in place till all air is evacuated - wipe excess RTV with paper towel...DONE

Removed grill and set aside, then removed burner with a 1/4 counter clock twist. Removed ground wire and igniter wire from burner. Set to side in order taken off. Remove the two screws on the panel that is on the back of the unit and slide it up and set it aside. Removed screws from side decorative panels each side (one top and one bottom) and slide panel toward the rear to remove from notch slot. Then removed the two screws on each side and back to remove top of range. On the side there are two screws together towards the rear, the one towards the front of the range need to be removed. Then removed four screws that held the pan under the range top that were screwed into the gas line supports. Then removed the two screws from rear that held the pan in place. Remove the pan and set aside. Lift the right gas line burner support up. Remove ground bottom, hot wires upper and igniter wires from spark module. Pop module out and replace with new one. Reverse process to complete repair. Cause that the wires do not get under the pan when reinstalling same

The 15-year-old Jen-Air stove started smelling really bad. I thought it was a dead animal stuck in the exhaust tube which runs under the floor to the outside. I flushed it out with clorine bleach, but it was still bad. It turned out to the be the grease filter. I washed it every week in the diswasher, but it just was not enough to get it clean enough. Finally, the grease went rancid and smelled really bad. This "repair" took about 30 seconds.

Turn off power, removed wires from switch, unscrewd lock nuts. Did the reverse to put the new switch with the exception of the the power which should always be turned off first. Took less than 5 min. to install. Wife happy!! which makes me happy.

:-) - Just removed the old one and replace with the new one. Nothing to it. Takes 30 seconds.

Extremely easy.
First, I turned powr off to appliance at electric panel (don't trust switches).
Next, I removed the 2 screws that held the panel cover, removed the dials, and removed 2 screws at each one (total eight) - this requrid a hex screw driver bit, which I had in my handy set.
I proceeded to loosen the panel, and disconnect the wires attached to the old switch (this may be tricky - mine came off easy, but did require care as to not to strip the wire from the clamp).
Once the old switch was removed and the plastic housing unscrewed, I attached the new fan assembly, and connected the wires, and reinstalled everything back in the same order.
(This is a good time to clean all the grease and dirt that has collected thru the years-before you put everything back).
Turned the power back on, and everything worked like before.
I figured I saved about 4 hours worth of labor (4x$50=$200 / minimum) plus any inflated part price I would have paid for a $20 part from PartSelect! It felt good!

Turn off the gas supply and unplug the electric supply. Remove the top grates and the burner cartridges. Remove 12 screws around the top cover and loosen the two screws for the fan switch. Pull the fan switch up and out of the way, remove the top cover. With a marking pen, label the four igniter switches and pull them off the gas valves. From underneath, remove the gas line from the pressure regulator, then remove the regulator from the pipe coming from the circular manifold. With a 3/16 socket (1/4 inch drive) or a 3/16 nut driver, remove the four screws that hold the manifold. Then from the top pull the manifold up and out. On the bottom, remove the screw (1/4 inch socket or nut driver) and remove the old gas valve. That's it. Now just put it all back together in reverse order. I used pipe joint compound on the pipe threads. Check for leaks with a soapy water solution. If I had to do this again, it would only take me half the time. I wasn't sure how everything came apart the first time..

This cartridge fits my JennAir Downdraft Slide In Rage, part No. JDS9865BDP. The burner cartridge replaces a downdraft cooking grill module that comes with the original stove/Oven.
The spark quit on the cartridge side. I re-inserted the original cooking grill, and it lit fine. There are two components to look at. The sparker, and the burner igniter (one per each burner). Since both failed to light, I ordered the spark controller.
PartSelect has a video on how to test for failure, but I couldn't find that again.
Two screws mount the controller, two wires re-connected. and works perfect.

Because the stove is over 10 years old the screws were very hard to loosen up and I needed to use WD 40 several times to loosen them,after that it was a snap for a 71-year-old woman.

Watched u tube video as supplied and followed instructions. Had trouble getting burners off so cleaned around edge of burners with fine bladed knife as suggested by other forum user and used oil filter type wrench to remove burner. There are three bumps on burner that hold it in place so need to turn anti clockwise to remove.

The front burner had a noticible flame coming from the base, so I originally purchased a single burner to replace it (you could see a corroded hole at the bottom). Upon taking the unit apart, I noticed the corrosion was much worse than met the eye. Given the age of the unit and that some parts were already becoming discontinued I decided to gut the whole thing and replace it all.
The burner unit slides out easily and after unscrewing the sides, you have to disconnect the wires from the underside of the igniters. The venturi tubes and igniters then unscrew from the underside of the burners which twist right out of the assembly. Re-Assembly is very intuitive looking at it and it all goes right back together as it came out. Took 45 minutes total and that includes fighting with some screws that had rusted onto the burner.
Reading some of the previous reviews, current prices are double to triple what other people did the repair for leading me to believe parts won't be available for much longer. Make the repair while you still can!

Put the new pad in and it was done. Very easy.

Two screws inside the exhaust box to take out the switch assembly and 2 nuts on the switch. Nothing to it

Remove switch cover with two screws ,remove two nuts holding switch in place ,remove switch,then reverse procedure with new switch.