Models
>
JGCP548WP00
JGCP548WP00 Jenn-Air Cooktop - Overview
Sections of the JGCP548WP00
[Viewing 3 of 3]Keep searches simple, eg. "belt" or "pump".
Screw, 8/18 x 3/8
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$5.42
In Stock
Screw
PartSelect #: PS12349731
Manufacturer #: W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$20.79
In Stock
Temperature Sensor
PartSelect #: PS11748765
Manufacturer #: WPW10131825
The temperature sensor measures the temperature inside the oven. If your oven is too hot, not heating evenly, is not heating enough when baking, or simply will not start, you could have a faulty tempe...
$89.97
In Stock
Grate Feet - Kit of 4
PartSelect #: PS2330208
Manufacturer #: W10185266
This kit contains 4 grate feet for a range. These are the feet to fit your burner grates so the burner will not scratch your cooktop. The are black in color and made of rubber. These feet are fitted w...
$7.88
In Stock
Palnut
PartSelect #: PS2365913
Manufacturer #: 7103P166-60
This palnut is designed for use in cooktops, ranges, wall ovens, dehumidifiers, and range hoods. The palnut is screwed onto a bolt on top of an ordinary nut, and locks the nut in place when the nut is...
$16.17
In Stock
Screw
PartSelect #: PS11744049
Manufacturer #: WP74003976
This screw is sold individually.
$5.36
In Stock
GRATE-BRNR
PartSelect #: PS12717468
Manufacturer #: W11344501
NOTE: As per manufacturer this part no longer includes the grate feet and they must be ordered separately.
$109.33
In Stock
Regulator
PartSelect #: PS11747235
Manufacturer #: WP9759091
This part makes sure that no gas is released until the igniter gets enough power to ignite the gas range and automatically cuts off the flow of gas at a certain pressure.
$175.15
In Stock
Burner Cap - Left Rear - Black
PartSelect #: PS11745755
Manufacturer #: WP8286816
Sold individually.
$64.62
In Stock
Questions And Answers for JGCP548WP00
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the JGCP548WP00
[Viewing 5 of 5]Oven is too hot
Fixed by
these parts
these parts
Show All
Little to no heat when baking
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
bUILT IN OVEN NOT COMING UP TO TEMPERATURE
Replaced oven temp sensor, removed oven door and interior racks for easy access to oven upper rear sensor access. Used philips head screw driver to remove both screws, gently pulled old senor out of reat oven wall until electrical connector clear of rear wall, disconnected connector, connected new sensor and gently pushed wiring and conne
... Read more
ctor back into opening, reinstalled door and racks. Ran open thru cycle and used oven thermometer to check temp. fast easy install
Read less
Parts Used:
-
Kenneth from BUFFALO, NY
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
5 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replace pads or feet on steel grate of gas stove
pull old ones out of legs. need to glue new ones in, they fit too loose. Some kits contain glue. get some high temp head gasket cement. a drop on each one is plenty. I used some old porcelain glue and hope it will hold. the pads are 2 bucks each plus shipping so don't let them get away!!!
Parts Used:
-
RICHARD from BROKEN ARROW, OK
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven will not maintain set temp
Remove rear panel - remove sensor from inside - unplug from rear - reverse to install - did not fix problem
Parts Used:
-
Sam from TINLEY PARK, IL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!