Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JGCP430ADP

JGCP430ADP Jenn-Air Cooktop - Overview

Get Parts and Repair Help for JGCP430ADP

If you know the cooktop repair part you need, you can browse the list of all parts on the JGCP430ADP, or you can search by name or part description. You can also find your part by where it is located on the JGCP430ADP by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your cooktop. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$40.68

Burner Head with Electrode

Order within the next 7 hrs and your part ships today!
$36.13

Burner Head

This part includes the spark igniter.

Order within the next 7 hrs and your part ships today!
$30.08

Burner Head with Electrode - Small

Order within the next 7 hrs and your part ships today!
$111.15

Pressure Regulator

A pressure regulator is a valve that will cut off the flow of liquid or gas when it reaches a certain pressure.

Order within the next 7 hrs and your part ships today!
$31.81

Nameplate - Stainless Steel

Order within the next 7 hrs and your part ships today!
$25.90

BEZEL

Order within the next 7 hrs and your part ships today!
$25.39

ORIFICE KI

$12.77

USE WPL 715500

Order within the next 7 hrs and your part ships today!
$23.99

PAN-DRIP

Order within the next 7 hrs and your part ships today!

USE WPL 7518P473-60

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ignitor stopped working on gas cooktop

  • Customer: Jeff from Lake Orion, MI
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 58 of 58 people found this instruction helpful
As others reported, there are 2 torx screws that need to be removed so that the burner element can be removed. One came out with a little effort, the other one did not as it was corroded. After breaking a torx bit, a second torx bit succeeded in breaking off the screw head. This then required a drill to drill out the broken shaft and then rethreading the s... read more

The ceramic insulator on the burner ignitor cracked & the spark shorted so that the burner would not ignite.

  • Customer: Loren from San Luis Obispo, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 27 of 29 people found this instruction helpful
Firts I removed the 2 screws that held the burber in place. Then I lifted the burner up & disconnected the wire that connected to the ignitor. Then I removed the one screw that held the ignitor to the burner. I then reversed these steps, replacing the cracked ignitor with the new one, replaced the screw holding it to the burner, then reconnected wire, return... read more

Cracked porcelain insulator on burner ignitor

  • Customer: chad from Houston, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 12 of 12 people found this instruction helpful
Removed grate and burner cover (held on by gravity - no tools needed) then removed the two screws holding down the burner itself. These screws are Torx screws so you will need a Torx bit set (looks like a phillips head screw driver but is star shaped). Once these screws are out, the burner lifts off to reveal two phillips head screws holding the ignitor in... read more