Models > JGBS18DET1WW

JGBS18DET1WW General Electric - Overview

Get Parts and Repair Help for JGBS18DET1WW

If you know the repair part you need, you can browse the list of all parts on the JGBS18DET1WW, or you can search by name or part description. You can also find your part by where it is located on the JGBS18DET1WW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your . We’ve also included any installation videos we have for JGBS18DET1WW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$2.52

Light Bulb - 40W

Sold individually.

$35.87

Flat Style Oven Igniter Kit

The flat style gas oven igniter included in this kit has a body length of 3-3/4". This kit comes with a mounting bracket and a wire connector with a plug. *Please note: the connector plug might need to be removed and spliced to range wiring using porcelain wire nuts. This part is used to heat your oven.

$2.23

Grate Bumper - Black

Sold individually.

$17.95

Burner Head - Medium - 9500

$18.57

Burner Cap - Medium

$12.82

Front Orifice Tube

$13.46

Double Porcelain Pan - Right Side

$5.55

Oven Light Socket - With Push In Receptacle

$4.48

Mini-Valve Knob

This knob accepts a D-shaped shaft.

$13.46

Double Porcelain Pan - Left Side

This pan sits under the burner to catch anything that may spill over to make cleaning up spills quick.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The igniter glowed, but never got hot enough to ignite the propane, so I did smell propane.

  • Customer: Sidney from Marysville CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 490 of 493 people found this instruction helpful
First, I removed the two screws that held the heat shield in place. Second, I removed the one screw that held a small wire covering. That covering kept the wires inside the back wall of the range. Third, I removed the two screws that held the Igniter Kit, and unplugged it from the back of the range. I then carefully put the new igniter in, and reassemble... read more

oven would not light or keep temp.

  • Customer: zack from corning CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 399 of 400 people found this instruction helpful
first I thought it was a faulty gas valve, so I pulled it out, started researching for a replacement part, found your site and started research. I discovered thhat the igniter was the culprit, that info. saved me about a week of time and a 100 bucks, so I installed the gas safety valve back in the oven, patience is the word for the day, you cross thread thi... read more

Oven wouldn't heat. This degraded over several weeks.

  • Customer: Durwood from Suffield CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 252 of 323 people found this instruction helpful
1. Pulled the 110V power plug. It was not necessary to turn off the gas; just be careful not to stretch or pinch the flexhose behind the stove.
2. Removed the oven door by opening a couple of inches then lifting upward.
3. Removed the warming drawer by pulling out to the stop, then pushing the small levers on the side of the track to release.
read more