Models > JGB920SEF2SS

JGB920SEF2SS General Electric Range - Overview

Get Parts and Repair Help for JGB920SEF2SS

If you know the range repair part you need, you can browse the list of all parts on the JGB920SEF2SS, or you can search by name or part description. You can also find your part by where it is located on the JGB920SEF2SS by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for JGB920SEF2SS parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.82

Light Bulb - 40W

Sold individually.

$38.36

Flat Style Oven Igniter Kit

The flat style gas oven igniter included in this kit has a body length of 3-3/4". This kit comes with a mounting bracket and a wire connector with a plug. *Please note: the connector plug might need to be removed and spliced to range wiring using porcelain wire nuts. This part is used to heat your oven.

$39.65

Oven Rack

Sold individually.

$89.55

Oven Sensor

This sensor detects the temperature within the oven cavity.

$5.77

Foot - Leveller

$16.87

Broiler Pan - Large

Includes the pan and grate.

$2.79

CLIP ELECTRODE

CLIP ELECTRODE

$71.59

Burner with Igniter

The igniter does not come with wire nuts. *** Please NOTE: The igniter connector may need to be cut off and wires spliced to the range wiring with the porcelain wire nuts.

$5.55

Oven Light Socket - With Push In Receptacle

$2.36

SCREW

Sold Individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

oven would not light or keep temp.

  • Customer: zack from corning CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 382 of 383 people found this instruction helpful
first I thought it was a faulty gas valve, so I pulled it out, started researching for a replacement part, found your site and started research. I discovered thhat the igniter was the culprit, that info. saved me about a week of time and a 100 bucks, so I installed the gas safety valve back in the oven, patience is the word for the day, you cross thread thi... read more

Oven wouldn't heat. This degraded over several weeks.

  • Customer: Durwood from Suffield CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 242 of 313 people found this instruction helpful
1. Pulled the 110V power plug. It was not necessary to turn off the gas; just be careful not to stretch or pinch the flexhose behind the stove.
2. Removed the oven door by opening a couple of inches then lifting upward.
3. Removed the warming drawer by pulling out to the stop, then pushing the small levers on the side of the track to release.
read more

Oven tempature was approximately 150 degrees to low

  • Customer: James from Austin TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 131 of 154 people found this instruction helpful
This repair is EASY if you know how to use an ohm meter. If not, seek help for this step.

SYMPTOM:
The oven (JKP27WOP3WG or JKP27WP3WG and many ovens like it ) was not getting hot enough. Verifying the cooking temperature with an typical oven thermometer, I was able to determine that the oven was cooking temperature was about 150 degrees t... read more