Models > JGB918SEL3SS > Instructions

JGB918SEL3SS General Electric Range - Instructions

All installation instructions for JGB918SEL3SS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JGB918SEL3SS
226-238 of 238
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

My oven bottom got rusty

  • Customer: Mary from Redondo Beach CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
I removed two bolts at the rear of the oven bottom. I pulled the old oven bottom out, and put the new oven bottom in. I put the two bolts back in and voila it looks like a new oven. Done in less than 15 minutes.

Oven Probe broke

  • Customer: Kathleen from Munt Laurel NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Ordered new probe

burner cap did not fit burner, causing ignition failure

  • Customer: Stephen from East Williston NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Replaced burner. New burner now ignites properly.

Convection fan came loose from shaft

  • Parts Used:
  • NUT
  • Customer: Thomas from Albuquerque NM
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Convection fan came loose from the shaft with a lout rattle and grinding as the fan spun down. Had to remove four metal screws to remove the fan cover. Initially tried to just put the nut back on to hold the fan. However, I could not get the nut to start, so I assumed that threads were stripped on the nut or the shaft. Ordered the replacement nut, hoping that it was the nut that was the problem. However, I had the same problem with the new nut. I could see no damage on the shaft. It finally occurred to me that the nut and shaft had left-hand threads (counter-clockwise to tighten). At that point, it was extremely easy to put the nut back on and tighten it. I did not try using the old nut, since I had already received the new one, but I'm certain that if I had come to that realization earlier, I could have saved time and money. So, if you have the same problem, try putting the nut on "backwards."

oven would not lite

  • Customer: Russell from Reidsville NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
took off old initer and then had take off that little cover to get to the end of the wire so i could unplug it .thorugh it was kind of britale it fell apart abit .plug the other one in and put it on &turn the oven on and it came right on!it went well.thank you

Bulb replacement

  • Customer: Judith from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I pulled down the wire around the glass cover...released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Forgot to remove the heat shield from the old part.

  • Customer: Joan from Watervliet NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Husband actually did the repair, It went really well except he forgot to remove the heat shield from the old part to attach to the new bottom. (His mistake!)

Oven took longer and longer to warm up, then wouldn't ignite at all.

  • Customer: Richard from Patterson LA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Unpluged power. 1. Removed all internals from the broiler. 2. Removed (3) protective heat shields. 3. Pulled glowbar plug through the access hole behind the gas piping. 4. Unplugged the glowbar. 4. Removed two glowbar holding screws and remove the glowbar. 5. Waited two and one half days to recieve the new part. 6. Reversed the process. NOTE: It really was not difficult at all, and the new part was original equipment so except for the delay in identifying, ordering, and receiving the part the whole process was very quick.

replacement of middle grate with griddle

  • Customer: D. J. from Hoschton GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Would have been easy, but I should have checked the measurements more carefully as it didn't fit. But the service from Part Select has been excellent!

it would glow, but it wouldn,t light

  • Customer: Robert from New Hope MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I took out the bottom broiler drawer and reached to the back of the oven. i loosened the screws,unplugged it and replaced the igniter and plugged it in and put it all together and it works great now.

My stove would not light at all.

  • Customer: Jajuan from Kansas City MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
It was easy I unplugged the stove but I left the gas alone. I used a flat head screw driver to take the oven sheet off. Then I unscrewed the oven lighter and the bracket holding it. Then I disconnected it and put the new one on. The hard part was letting the wd-40 dissolve for the rusty screws

Replaced damaged oven rack

  • Customer: Vicki from Irvine CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.

Gas oven would not ignite

  • Customer: Russell from Maple Shade NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Using your information that was posted i order the part that was most likely the problem. The video was spot on for the replace part.
All Instructions for the JGB918SEL3SS
226-238 of 238