Models > JGB918SEL1SS > Instructions

JGB918SEL1SS General Electric Range - Instructions

All Instructions for the JGB918SEL1SS
1 - 15 of 75
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Cracked Burner Knob Stem
One of my plastic burner knobs cracked. I ordered a replacement knob using the correct part number, but apparently the style of that part has changed slightly over the past four years. My new knob did not match the existing knobs. I ended up buying more new knobs so they all match.
Parts Used:
BURNER KNOB KIT
  • Michael from Oakland, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
138 of 183 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner would not lite
openend stove top disconnected wire pushed out old sparker inserted new one closed lid game over
Parts Used:
Top Burner Spark Electrode
  • Glen from Kenner, LA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
23 of 33 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pies Boiled Over And Baked On Oven Bottom
Removed the two screws put the heat shield off the old one onto the new one put new bottom in and tightened two screws. Done #38. 69 Cost of part with shipping cost included.
Parts Used:
BOTTOM OVEN AND DEFLECTOR ASM
  • Marjorie from Yucca Valley, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
17 of 21 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven rack missing when I purchased the house
I was very pleased with how quickly the new oven rack arrived and it was a perfect fit. Thanks.
Parts Used:
Oven Rack
  • Patricia from Houston, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
18 of 27 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Interior light needed replaced
Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.
Parts Used:
Light Bulb - 40W
  • Leo from TWIN FALLS, ID
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
15 of 25 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Twice I ordered the oven light bulb & each time the light bulb was defected
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
Parts Used:
Light Bulb - 40W
  • Barbara from BELLEVUE, WA
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    Less than 15 mins
14 of 23 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed extra oven space
Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.
Parts Used:
Oven Rack
  • noreen from flushing, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
11 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven post mini explosion sounding
the flame spreader through the years, developed a hole above the glow coil causing the above trapped gas between the oven pan and spreader to ignite. by replacing the flame spreader the problem is gone and is now working properly. thank you, parts select for being there when i needed the part and also being reasonably priced. mike marino
Parts Used:
DEFLECTOR OVEN
  • Mchael J. from Chesterfield, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
13 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven bottom tray would not clean up.Looked like finish was off it
removed two screws and took out bottom tray and put the new one in and replaced the screws.DId it my self.
Parts Used:
BOTTOM OVEN AND DEFLECTOR ASM
  • Jim from 29 Palms, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
11 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Change bad/broken igniter on gas stove top burners
Very simple repair with no tools required. Turn off power to stove. Remove grates, remove burner, pull old Top Burner Spark Electrode up being careful not to jerk it up hard - wiggle if necessary, unplug wire from old electrode, plug wire into new electrode making sure it fits snug - if not, squeeze it closed a little at a time until it fits snug, push new igniter into place being careful not to force it and crack the ceramic body. Install burner being careful not to damage the electrode, Install grates. Turn power back on and test to make sure it works. It took me all of 15 minutes to change 2 burner spark electrodes. The only bad thing about this repair is that the shipping costs as much as the parts.
Parts Used:
Top Burner Spark Electrode
  • James from Kaplan, LA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The griddle needed to be replaced
Lifted the old one off and placed the new one on. Fits perfectly and looks great!
Parts Used:
Griddle
  • brigitte from vacaville, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner Knobs were melted and needed to be replaced.
Ordered the parts and put them on. No tools, no problems
Parts Used:
BURNER KNOB KIT
  • Catherine from S WELLFLEET, MA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
6 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Hole burned through deflector oven and metal dropped onto igniter and burned it out
Removed bottom shelf from inside oven, turned it obj and replaced the oven deflector with only a screwdriver
Parts Used:
DEFLECTOR OVEN
  • Scott from ARDMORE, PA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old blackened oven racks
Replaced old with new.
Parts Used:
Oven Rack
  • Roger from Falls Church, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
8 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
none
slid the old ones out and slid the new ones in. done
Parts Used:
Oven Rack
  • Michael from Laughlin, NV
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JGB918SEL1SS
1 - 15 of 75
Back to Top