Models > JGA8100ADW

JGA8100ADW Jenn-Air Refrigerator - Overview

Get Parts and Repair Help for JGA8100ADW

If you know the refrigerator repair part you need, you can browse the list of all parts on the JGA8100ADW, or you can search by name or part description. You can also find your part by where it is located on the JGA8100ADW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for JGA8100ADW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Exact Part matches for your search term [Viewing 1 of 1]

$410.71

Gas Burner Cartridge with Grates

This part number matches the current model number "JGA8100ADW".

Manufacturer's Number: JGA8100ADW For Designer Line gas and Dual-Fuel cooktops. One-piece sealed burners with porcelain-on-cast iron burner grates. White with Grey grates, also available in black. May not be exactly as shown.

Sections of the JGA8100ADW [Viewing 1 of 1]

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$16.78

Top Burner Igniter

This top burner igniter comes with a mounting bracket.

$5.40

Bumper Pad Set of 4

***NOTE: This part has been substituted by the manufacturer and may not appear the same as the original but should function the same. These pads go on the bottom of your gas cooktop grates to prevent them from moving and scratching the top of your appliance.

$27.66

Spark Igniter Set

$34.27

Burner Head

$3.86

Brass Seal

$2.70

SCREW

$4.11

SCREW

$49.02

USE WPL 74005894

$84.10

VENTURI

$3.54

GUARD- COR

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

gas burner ignitor failure

  • Customer: roy from East Providence RI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 52 of 59 people found this instruction helpful
Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed that rust and dirt ha... read more

burner would not light; ignitor did not produce spark

  • Customer: Candace L. from Woodinville WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 10 people found this instruction helpful
Take a few screws off the back of the slide in burner module. Take off the back. Unscrew the ignitor screw, remove ignitor carefully, replace with the new ignitor, put the screw back in, put the back back on, try it out! Ours worked after a couple of tries - don't know if the ignitor had to "rev up" by several sparks or we just didn't have it properly ins... read more

Spark igniter out

  • Customer: Patricia from Overland park KS
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 9 people found this instruction helpful
The primary spark igniters failed. Take the (small) screws out of the sides and bottom of the pan. The front of the pan must be removed from the bottom, because the front burner igniter wire is too short to allow reassembly once attached. Only other is the screws for the attachment bracket are larger than the holes. Suggest routing them out slightly to get t... read more