Models
>
JGA8100ADB11
JGA8100ADB11 Jenn-Air Range - Overview
Sections of the JGA8100ADB11
[Viewing 1 of 1]Keep searches simple, eg. "belt" or "pump".
Top Burner Igniter
PartSelect #: PS2082000
Manufacturer #: 74004053
This is a surface burner igniter, also known as a top burner ignitor and stove top spark electrode. It is used to generate the spark that lights the surface burner. If your stove will not start, eleme...
$41.20
In Stock
Spark Igniter Set
PartSelect #: PS11744110
Manufacturer #: WP74005890
This part provides the spark to the burners.
$86.55
In Stock
Brass Seal
PartSelect #: PS11744111
Manufacturer #: WP74005893
This is the replacement brass seal for your range or cooktop. It is made of brass and is approximately 1 inch in diameter. This part may also be known as the surface burner orifice holder seal. It pre...
$8.04
In Stock
Double Burner Grate - Black
PartSelect #: PS11744605
Manufacturer #: WP7518P483-60
This is one double burner grate - which means you get one grate that covers two burners.
$177.63
In Stock
Range Surface Burner Grate
PartSelect #: PS3406613
Manufacturer #: 7518P482-60
The surface burner grate provides a stable surface for cookware on the surface burner.
No Longer Available
Questions And Answers for JGA8100ADB11
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the JGA8100ADB11
[Viewing 3 of 3]Will Not Start
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
gas burner ignitor failure
Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed t
... Read more
hat rust and dirt had built up around burner to pan connection.I used my oil filter wrench to turn slightly the burner to remove it from the pan to clean.Reassembled in reverse order.
Read less
Parts Used:
-
roy from East Providence, RI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
139 of 157 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner would not light; ignitor did not produce spark
Take a few screws off the back of the slide in burner module. Take off the back. Unscrew the ignitor screw, remove ignitor carefully, replace with the new ignitor, put the screw back in, put the back back on, try it out! Ours worked after a couple of tries - don't know if the ignitor had to "rev up" by several sparks or we just didn't
... Read more
have it properly installed at first. Anyway, very easy. Did it in my pajamas on a Saturday morning.
Read less
Parts Used:
-
Candace L. from Woodinville, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
16 of 20 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spark igniter out
The primary spark igniters failed. Take the (small) screws out of the sides and bottom of the pan. The front of the pan must be removed from the bottom, because the front burner igniter wire is too short to allow reassembly once attached. Only other is the screws for the attachment bracket are larger than the holes. Suggest routing them o
... Read more
ut slightly to get them to grip the screws. Otherwise it is quite simple. Pull the connections with a needlenose and press the new wire connection back on firmly. Screw the screws back in the pan.
Read less
Parts Used:
-
Patricia from Overland park, KS
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
18 of 26 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!