Models > JFC2089HES > Instructions

JFC2089HES Jenn-Air Refrigerator - Instructions

All Instructions for the JFC2089HES
766 - 780 of 1079
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Both light bulbs had been replaced, but lights did not turn on.
I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.
Parts Used:
Refrigerator Door Switch
  • Richard from Arlington, MA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
no ice
Easy
Parts Used:
Replacement Ice Maker
  • Robert from Mondovi, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Light on refrigerator went on to replace filter
Just replaced a water/ice filter..
Parts Used:
Refrigerator Water Filter
  • CAROL M from TUCSON, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Broke the arm off the food compartment rocker switch
After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.
Parts Used:
Refrigerator Door Switch
  • David from St. Pete Beach, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Installed new Ice Maker
Followed the instructions from the excellent video by Steve on your website which made the installation easy.
Parts Used:
Replacement Ice Maker
  • James from Chatsworth, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Loud, non-rythmic clicking noise shortly after the compressor comes on, continuing for several seconds.
Replaced the "Run Capacitor. The non-rythmic clicking associated with the compressor coming on continues. The problem was obviously not the Run Capacitor". I don't know what to do next. Any suggestion would be appreciated.

Thanks,

Phillip
Parts Used:
Run Capacitor
  • PHILLIP from SUN CITY CENTER, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Plastic clips that held in clear plexiglass broke off
Very easy to replace the old broken piece with the new one. Simple
Parts Used:
Refrigerator Pantry Drawer Door Cover
  • Kenneth from Howell, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Filter needed changing
Simple! Pop the case open. Counterclockwise to remove old filter. Wipe out excess water. Unwrap new filter; remove tab. Place in filter holder; turn clockwise. Close case. Run water to remove air. Couldn't have been easier!
Parts Used:
Refrigerator Water Filter
  • Lynn from Rome, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Compressor would not start
Unplug Refrigerator remove lower back panel to expose compressor.Unplug Capactor relay assembly,Plug in new start assenbly,and then the refrigerator to elect'outlet .Compressor srarted right up . Real easy fix simple tools to perform change out. Thanks!!! Saved a bunch of $$$$$ .
Parts Used:
Compressor Start Device and Capacitor
  • Raymond from Chicago, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
My original ice maker was leaking
I went online to PartSelect to see how much I'd expect to pay for the ice maker assembly if I called an appliance repairman to fix it. Instead I found an awesome, very well described video on how to do it myself. I ordered the part and paid ground shipping, but received it the next day!! Installation was a breeze (except I got help removing the electrical jacket because it was an awkward angle and I was afraid that I would damage it). The experience did as much for my single, 55 yr. old self esteem as it did for my wallet. Thank you PartSelect! I'll be back!
Parts Used:
Replacement Ice Maker
  • Joyce from West Palm Beach, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Not making ice
Repair was very easy. I watched the video and read the descriptions by other customers and it was just as described. Had ice again in about 4 hours and has been working great since.
Parts Used:
Replacement Ice Maker
  • Larry from Sun City, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken pin holding pantry door
Was a snap. Took out the draws. Removed glass plate. Unscrewed endcap using socket set. Removed rail. Screwed rail to new endcap. Screwed in encap. Replaced all draws and plates. Didn't take more than ten minutes.
Parts Used:
Pantry End Cap - Left Side
  • Michael from Linville, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Wrench set
Was this instruction helpful to you?
Thank you for voting!
No ice.
(1) Watched the PartSelect installation video. (2) Placed Order. Arrived in two days, regular delivery. (3) Opened package. (4) Selected installation tool. (5)Removed old Ice Maker Assemply (6) Replaced w/new. Ice in a couple of hours. Video & order/delivery aside, the entire process took less than 10 minutes including selecting tool and opening package. PartSelect video very helpful.
Parts Used:
Replacement Ice Maker
  • Dennis from Lexington, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Ordered ejector arm.
No instructions with part. Found a picture on line and changed the arm, but it didn't fix the problem. Fairly easy after figured out what needed to be done to get to the part.
Parts Used:
Ejector Arm
  • Joyce from Springfield, MO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
water running in ice cube tray
After watching the video witch was GREAT help THANK YOU
Parts Used:
Replacement Ice Maker
  • Thomas from Sussex, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JFC2089HES
766 - 780 of 1079
Back to Top